Bedienungsanleitung Mitsubishi WS65615 (Seite 36 von 100) (Englisch)

33003

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Edit NetCommand

, Adding an A/V Receiver, continued

A/V Receiver Learn Screen

Figure 9

1. Press ADJUST or on the TV remote to select the

check box for each function to be learned.

2. Press ENTER and the function name will begin to

flash to confirm the ready-to-learn status.

3. Press the button on the A/V Receiver’s remote

control that corresponds to the selected function,

A check mark will appear and the function name

will stop flashing. This confirms the signal learned

status.

4. To test the learned command, press ENTER on

the TV remote. The A/V Receiver will perform the

selected function. The A/V Receiver needs to be

turned on and the IR emitters properly placed for

the test to be successful (see page 22 for IR emitter

placement).

5. Repeat for each function to be learned.

6. To erase a learned function, highlight the check box

for that function and press CANCEL.

7. When the function signals have been learned, press

ADJUST to select Next> and move to the Name

screen.

A/V Receiver Input Learn Screen

Figure 8

NetCommand can now learn the remote control signals

used to select each input on the A/V Receiver.

1. Press ADJUST or on the TV remote to select the

check box for each function to be learned.

2. Press ENTER and the function name will begin to

flash to confirm the ready-to-learn status.

3. Press the button on the A/V Receiver’s remote

control that corresponds to the selected function.

A check mark will appear and the function name

will stop flashing. This confirms the signal learned

status.

4. To test the learned command, press ENTER on

the TV remote. The A/V Receiver will perform the

selected function. The A/V Receiver needs to be

turned on and the IR emitters properly placed for

the test to be successful (see page 22 for IR emitter

placement).

5. To customize the input names, press ADJUST to

move to the Input Name text box and then press

ADJUST or and ENTER to select each letter of

the name. These names will appear on the Review

screen as the A/V Receiver’s input names.

6. To erase the learned input signal, highlight the check

box for that input and press CANCEL.

7. Repeat for each connected input.

8. When the input selection signals have been learned

and the inputs named, press ADJUST to select

Next> and move to the A/V Receiver Learn screen.

Figure 8. A/V Receiver Input Learn screen

Figure 9. A/V Receiver Learn screen

Hint: If your A/V Receiver remote control uses a single

button for both Power On and Power Off, do not learn

the Power Off function. If your A/V Receiver uses a

single button to toggle between digital and analog

sound, then learn only Analog to Digital. If your A/V

Receiver automatically switches between analog and

digital audio, then you will not need to learn either

Analog to Digital or Digital to Analog functions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WS65615 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info