Bedienungsanleitung Mitsubishi XD8500U (Seite 64 von 79) (Englisch)

549867

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

EN-64

Replacing the lamp

This projector is equipped with 2 lamps to project

images. This lamp is a consumable. It may burn out

or its brightness may decrease during use. In such

cases, replace the lamp with a new one as soon as

possible. Be sure to replace the lamp with a new lamp

separately sold that is exclusive to this projector.

Contact your dealer for purchase of the lamp.

Spare lamp VLT-XD8600LP

Warning:

• Becarefulnottodropthelampxingscrewsinto

the inside of the projector. Don’t put a metal piece

or ﬂammable object into the projector. Using the

projector with any foreign object present inside

may result in electric shock or ﬁre. When you can’t

remove the foreign object from the inside, contact

your dealer for removal.

• Donottouchthelampwithbarehandsorgive

a shock to the lamp. Attach the lamp properly.

Improper handling may cause explosion.

• Besuretoinstallthelampsecurely.Whenthelamp

isn’t installed properly, it won’t illuminate. Improper

installation may also result in ﬁre.

• Don’tshaketheremovedlampordon’tliftitabove

your face. You may be injured in your eye by ﬂying

or falling glass fragments.

• Don’treplacethelampimmediatelyafteruse

because the lamp cover is very hot. You may get

burned. Turn off the power using the POWER

button. After the lamp goes out, wait about 2

minutes until the intake and exhaust fans for

cooling the lamp stop rotating. Then unplug the

power cord, and wait at least 1 hour to allow the

lamp to cool down enough to the touch.

Interval of lamp replacement

The recommended interval of lamp replacement is

about 4000 hours

*1*2

of consecutive use. Such interval

differs depending on the operating environment

and may be shorter than 4000 hours

*1*2

. Decrease

in luminescence and/or color brightness indicates

that the lamp needs to be replaced. When the lamp

operation time exceeds 3000 hours

, the indicator

will blink alternately between green and red (while the

lampislit;whenthelampisnotlit,theindicatorwill

be lit red only) and the lamp replacement message

will appear on the screen for 1 minute everytime the

lamp is turned on. When the lamp has been used

for about 3800 hours

, the replacement message

(LAMP REPLACEMENT) will appear on the screen for

1 minute every 20 hours

thereafter. When the lamp

operation time exceeds 4000 hours

*1*2

, the projector

automatically shuts off.

*1: Duration when LAMP MODE of the INSTALLATION 1

menu is set to LOW. When it is set to STANDARD, this

duration will be shorted.

*2: When LAMP MODE is set to STANDARD, this duration

will be shorted to 2000 hours.

Caution:

• Don’tremovethelampforanypurposeotherthan

replacement. Unnecessary removal of the lamp

may result in a breakdown.

• Thisprojectorusesahigh-pressuremercurylamp

as the light source. The high-pressure mercury

lamp may explode or fail to illuminate permanently

because of an impact, scratch, or deterioration

through use. The period of time until explosion or

permanent failure to illuminate varies considerably

from lamp to lamp, depending on operation

conditions. Therefore, the lamp may explode soon

after the start of use.

• Thepossibilityofexplosionofthelampincreasesif

you use it beyond its replacement period. When the

instruction of lamp replacement appears, replace it

with a new one immediately even if the lamp is still

lighting normally.

• Whenthehigh-pressuremercurylampexplodes,

glass fragments will scatter inside or outside the

lamp box and the gas charged inside the lamp

will diffuse inside or outside the projector. The gas

inside the lamp contains mercury. Be careful not

to breathe it or avoid it from entering your eye or

mouth. If you should breathe it or if it should enter

your eye or mouth, see a doctor immediately.

• Intheeventthatthehigh-pressuremercury

lamp exploded, glass fragments may have been

scattered inside the projector. Ask your dealer to

replace the lamp and to inspect the inside of the

projector. When you clean or replace the lamp by

yourself, be sure to hold the handle of the lamp.

You may get injured by glass fragments.

• Whenremovingthelampfromtheceiling-mounted

projector, use the lamp replacement tray packed

with the projector or option lamp to prevent glass

fragments from scattering.

• Besuretousethelampexclusivetothisprojector,

VLT-XD8600LP. Use of other lamps may cause a

failure of the projector.

Before replacing the lamp

1. Check which indicator (for LAMP 1 or LAMP 2) is

illuminating or blinking.

LAMP 2 indicator

LAMP 1 indicator

• Forthestatusesoftheindicatorsurgingyouto

replace the lamps, see page 73.

• Replacethelampindicatedbytheilluminating/

blinking indicator using the following procedure.

• Whenbothindicatorsareilluminatingorblinking,

replace both lamps at the same time.

To replace the lamp:

1. Unplug the power cord from the outlet or appliance

inlet.

2. Loosen two screws (a) that are securing the lamp

cover using a Phillips screwdriver and remove the

lamp cover (b) from the projector.

(a)

(b)

Mitsubishi XD8500U Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi XD8500U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info