Bedienungsanleitung Mitsubishi XL5U (Seite 27 von 34) (Englisch)

493635

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

EN – 27

ENGLISH

Images aren't projected correctly.

Problem

Projected images are

shaking.

Projected images are

displaced.

Projected images are

distorted.

Projected images are

dark.

Projected images are

blurred.

Afterimages persist on

the screen.

Red, blue, and green

dots appear in projected

images.

Black dots appear in

projected images.

Fine streak pattern

appears in projected

images.

Projected images (and/

or audio) appear wavy

and distorted.

Tint in projected images

is incorrect.

Only the motion areas

in the images supplied

from the computer

aren't displayed.

Projected images are

obscured.

Cause and solution

• Check that the cable connected to the external device isn't intermittent.

• Connect the cable's plug with the external device's connector firmly.

• Press the AUTO POSITION button.

• Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See

page 19.)

• Adjust the projector and the screen so that they are perpendicular to each other. (See page

12.)

• Adjust BRIGHTNESS in the IMAGE menu. (See page 18.)

• Replace the lamp. (See page 24.)

• Adjust the focus. (See page 13.)

• Clean the lens.

• Press the $ or % button on the remote control to eliminate flicker.

• Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 18.)

• Adjust the projector and the screen so that they are perpendicular to each other. (See page

12.)

• This phenomenon is improved by keeping projecting an evenly bright image. (Such "image

burn-in" phenomenon where afterimages persist on the screen may occur if a stationary

image is kept displayed on the screen for a long time.)

• This phenomenon is unique to LCD projector and isn't a product malfunction.

(A small number of pixels always stay on or off, which are not malfunctions. More than

99.99% of the pixels are effective.)

• It occurs because of interference with the screen and isn't a product malfunction. Change

the screen or readjust the focus of the projector.

• Connect the cable's plug with the external device's connector firmly.

• Keep the projector away from equipment generating interfering radio waves.

• When the keystone adjustment is carried out, the image may not be displayed correctly

because of the type of input signal. This isn’t a product malfunction. In this case, readjust

the keystone so that the amount of keystone correction is as small as possible.

• Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 17.)

• Check that the cable connected to the external device isn't broken.

• This is caused by the computer being used. Contact the manufacturer of your computer.

• Match the output resolution of your computer with the resolution of the projector. For the

method to change the output resolution of the computer, contact the manufacturer of your

computer. (See page 32 or 33.)

• Some images and texts appear obscured during the keystone adjustment. In such cases, use

the projector without applying the keystone adjustment. (See page 12.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi XL5U Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info