Bedienungsanleitung Mitsubishi XL7100U (Seite 13 von 68) (Englisch)

493657

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

EN-13

Setting HIGH ALTITUDE MODE

t 4FU)*()"-5*56%&.0%&JOUIF'&"563&NFOV

according to the altitude at which you use the

projector. The default setting is STANDARD.

t 4FMFDU45"/%"3%XIFOVTJOHUIFQSPKFDUPSBUBO

altitude from 0 to 1500 meters.

t 4FMFDU)*()"-5*56%&XIFOVTJOHUIFQSPKFDUPSBU

an altitude from 1500 to 2700 meters.

Important:

t *GZPVTFMFDU45"/%"3%XIFOVTJOHUIFQSPKFDUPS

at an altitude higher than 1500 meters, the

projector may break down or fail.

t 8IFOZPVVTFUIFQSPKFDUPSJOUIF)*()"-5*56%&

mode, only ﬂoor installation and ceiling installation

are allowed.

t 8IFOZPVTFMFDU)*()"-5*56%&JO)*()

ALTITUDE MODE, LAMP MODE setting

automatically changes to LOW.

(See page 31 for menu setting.)

1. Display the FEATURE menu.

2. Select HIGH ALTITUDE MODE by pressing the 

or  button.

HIGH ALTITUDE MODE

STANDARD

3. Press the ENTER button.

HIGH ALTITUDE MODE

STANDARD

4. Select STANDARD or HIGH ALTITUDE by

pressing the  or  button.

5. Press the ENTER button.

Setting IMAGE REVERSE

Set IMAGE REVERSE in the INSTALLATION menu

according to the orientation of the projector. The

default setting is OFF.

t 4FMFDU0''GPSUIFDPNCJOBUJPOPGnPPSJOTUBMMBUJPO

and front projection.

t 4FMFDU.*3303*/7&35GPSUIFDPNCJOBUJPOPG

ceiling installation and front projection.

t 4FMFDU.*3303GPSUIFDPNCJOBUJPOPGnPPS

installation and rear projection.

t 4FMFDU*/7&35GPSUIFDPNCJOBUJPOPGDFJMJOH

installation and rear projection.

(See page 31 for menu setting.)

1. Display the INSTALLATION menu.

2. Select IMAGE REVERSE by pressing the  or 

button.

OFF

IMAGE REVERSE

3. Select OFF, MIRROR, INVERT or MIRROR INVERT

by pressing the  or  button.

Correcting skewed or distorted

image

For the best projection, project images on a ﬂat screen

installed at 90 degrees to the ﬂoor. If necessary, tilt the

projector using the two adjustment feet on the bottom

of the projector.

Adjustment feet

Screen

1. Tilt up the projector to the appropriate angle.

2. Rotate the adjustment feet for ﬁne adjustment.

Important:

t %POUUSBOTQPSUUIFQSPKFDUPSXJUIJUTBEKVTUNFOU

feet extended. Otherwise the adjustment feet may

be damaged.

When ﬁne streaks are seen on

projected images

This is due to interference with the screen surface and

is not a malfunction. Replace the screen or displace

the focus a little. (See page 12 for focus adjustment.)

When the projected image is

distorted:

When the projected image is distorted, carry out any

of the KEYSTONE, CORNERSTONE, and CURVED-

mode adjustments to correct the distortion.

When the image distorts in a trapezoid shape, use the

KEYSTONE-mode adjustment. For ﬁne adjustment

of the image shape, use the CORNERSTONE-mode

adjustment. To adjust the image projected on a curved

surface, use the CURVED-mode adjustment.

When you press the ENTER/GEOMETRY button on

the projector or the GEOMETRY button on the remote

control, the menu switches in the order of KEYSTONE,

CORNERSTONE, CURVED, regular display, KEYSTONE...

Setting up your projector (continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi XL7100U Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi XL7100U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info