Bedienungsanleitung Monacor DMR524 (Seite 23 von 60) (Englisch)

632632

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

MENU FUNCTION

-19-

(1) Detection Setup

Move the cursor to “DETECTION SETUP”, and press ”ENTER”. You will see a similar screen as the following:

DETECTION

DETECTION SETUP

TITLE DET AREA LS SS TS RE ALARM

DETECTION TIMER 01 ON SETUP 07 03 02 10 LOW

02 OFF SETUP 07 03 02 10 OFF

03 OFF SETUP 07 03 02 10 LOW

04 OFF SETUP 07 03 02 10 HIGH

PREV NEXT

The submenu items are described below:

1) TITLE:

Show the camera title of each channel set in “CAMERA”.

2) DET: Select if you want to activate the motion detection function for the selected channel (ON/OFF).

3) AREA

Press “ENTER” button to set the detection area. You will see similar screens as the following:

Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection.

Note: If the connected video output device is LCD monitor, but the “MONITOR OUT” setting in “DISPLAY”

menu is "MAIN", the motion detection area setting will be disabled.

4) LS (Level of Sensitivity)

“LS” is to set the sensitivity of comparing two different images. The smaller the value is, the higher sensitivity for motion

detection. The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The default value is 07.

5) SS (Spatial Sensitivity)

“SS” is to set the sensitivity for detecting the size of one object (the number of the grids) on the screen. The smaller the

value is, the higher sensitivity for motion detection.

The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The default setting is 03.

Note: The default setting of SS is 03, which means once an object is detected more than 3 grids, the system

will get triggered. So the value of SS must be less than the number of grids that you set up for the

motion detection area.

6) TS (Time of Sensitivity)

“TS” is to set the sensitivity regarding how long one object stays in the detection area and triggers the recording. The

smaller the value is, the higher sensitivity for motion detection.

The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The default setting is 02.

7) RE (Reference)

“RE” is to set a reference for detection. The default value is 10, which means the DVR will compare 10 continuous

images at one time according to the sensitivity of LS, SS, TS simultaneously.

The bigger the value is, the higher sensitivity for motion detection. The highest sensitivity is 61.

8) ALARM

Select LOW / HIGH for the alarm polarity. The default alarm value is OFF.

Press “ENTER” to confirm

the start area.

Press “LEFT” or “RIGHT” to

choose the width of the area

Press “UP” or “DOWN” to choose

the height of the area, and press

“ENTER” again to confirm.

You can also up set up

multi-detection areas.

Press “－” to set the whole

area under detection

Press “＋” to set the whole

area undetected

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Monacor DMR524 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Monacor DMR524

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info