Bedienungsanleitung Montiss CSC620 (Seite 23 von 33) (Deutsch, Englisch, Holländisch, Französisch)

803064

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Filling the water tank

Remove the water tank from the main body, open the water tank cup anticlockwise, fill the water

tank from the tap and close. Install the water tank back onto the main body (D) until it clicks into

place.

Operation

Plug the steam mop into the mains power supply. When it turns on the indicator light will turn red to

show that it is heating up.

The steam mop will take approximately 30 seconds to warm up. Once it has reached the correct

temperature, the indicator light will change blue. The steam mop is now ready to use.

MAINTENANCE AND CLEANING

Ensure that no water penetrates the device. Never submerge it in water or any other liquid.

Do not turn on the steam mop during use.

Cleaning the device

1. Take the plug from the socket before you start cleaning the device. Always allow the device to

cool down properly before you start cleaning it.

2. Take the microfiber cleaning pad from the device. The microfiber cleaning pad is washable.

3. Clean the non-electrical parts of the steam mop in warm soapy water and dry thoroughly. Wipe it

clean with a soft, dry cloth. Do not use harsh or abrasive cleaners or detergents

Attention: Never immerse the electrical components in water or any other liquid.

Please note: This steam mop is not suitable for dishwasher use

Cleaning the microfiber cleaning pad

The micro fiber cleaning pad can be washed at 40° (do not use bleach or fabric softener, do not

tumble dry!). Leave the microfiber cleaning pad to dry for 24 hours.

Remove Limescale

If the steam mop begins to produce steam slower than usual or stops producing steam completely,

you may need to remove limescale. Limescale can develop over time on the metal parts and greatly

affects performance. It is necessary to remove limescale on a regular basis, every 25-50 times you

use a full tank of water or at least once a month, especially in areas with hard water.

To remove the limescale:

1. Prepare a solution of white vinegar and tap water and add it to the water tank.

2. Secure and position the steam mop to ensure that the steam released is aimed away from the

floor or surrounding objects and surfaces

3. Plug the steam mop into the mains power supply and turn it on. Allow it to produce steam until

all of the solution is used

4. Repeat the above procedure as often as necessary, then fill the tank with fresh water

5. Fill the tank to the maximum level with fresh water, switch it on and release steam until the

water tank is empty

If there is a blockage in the steam nozzle, use the cleaning needle to clean the blockage along with

the descaling solution. Insert the cleaning needle into the steam nozzle hole

to clear the blockage.

Warning: Be sure that the steam mop is switched off and has cooled fully.

After using the cleaning needle, add the descaling solution to the tank and

follow the steps to remove limescale.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Montiss CSC620 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info