Bedienungsanleitung Morco GB24 SII (Seite 4 von 36) (Englisch)

646332

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SECTION 1 - USERS INSTRUCTIONS

Minimum Clearances

Clearances of 165mm (6 1/2”) above, 100mm (4”) below,

2.5mm (1/8”) at the sides and 450mm (17 3/4”) at the front of

the boiler casing must be allowed for servicing.

Bottom clearance

Bottom clearance after installation can be reduced to 5mm.

This must be obtained with an easily removable panel, to

enable the consumer to view the system pressure gauge, and

to provide the 100mm clearance required for servicing.

To light the boiler. Refer to Boiler Controls

1. CHECK THAT THE ELECTRICITY SUPPLY TO BOILER IS

OFF.

2. Set the mode knob control (A) to ‘Off’.

3. Set the Domestic Hot Water temperature control (B) and

Central Heating temperature control (C) to ‘max’.

4. Ensure that all hot water taps are turned off.

5. Switch ON electricity to the boiler and check that all

controls, e.g. timer and room thermostat, are ON (refer to

mechanical timer instructions - Page 6).

6. Set the mode knob control to winter (

If there is a central heating demand the boiler will commence

the ignition sequence.

Note. In normal operation the boiler status display (D) will

show codes:

Standby - no demand for heat.

CH being supplied.

DHW being supplied.

DHW preheat.

During normal operation the burner on indicator (E) will remain

illuminated when the burner is lit.

Note:Iftheboilerfailstolightafterveattemptsthefault

code

will be displayed.

RESET PROCEDURE

To reset boiler, turn the mode control knob (A) to reset position

and immediately turn knob back to required setting. The boiler

will repeat the ignition sequence if a heat demand is present.

If the boiler still fails to light consult a Gas Safe Registered

Engineer,orinothercountriesaqualiedandcompetentGas

Installer.

Introduction

The Morco GB Series II is a wall mounted, room sealed, condensing

combination boiler, featuring full sequence automatic spark ignition

and fan assisted combustion.

Duetothehighefciencyoftheboiler,condensateisproducedfrom

theuegasesandthisisdrainedtoasuitabledisposalpointthrough

a plastic waste pipe at the base of the boiler. A condensate ‘plume’

willalsobevisibleattheueterminal.

The Morco GB Series II is a combination boiler providing both central

heating and instantaneous domestic hot water.

Safety

Current Gas Safety (Installation & Use)

Regulations or rules in force.

In your own interest, and that of safety, it is the law that this boiler

must be installed by a Gas Safe Registered Engineer, in accordance

with the above regulations.

Inothercountriestheinstallationmustbecarriedoutbyaqualied

and competent Gas Installer. In the approved country the boiler is

installed, this must be in accordance with their current rules in force.

It is essential that the instructions in this booklet are strictly followed,

for safe and economical operation of the boiler.

Electricity Supply

This appliance must be earthed.

Supply: 230 V ~ 50 Hz. The fusing should be 3A.

Important Notes

 This appliance must not be operated without the casing correctly

ttedandforminganadequateseal.

 If the boiler is installed in a compartment then the compartment

MUST NOT be used for storage purposes.

 If it is known or suspected that a fault exists on the boiler then it

MUST NOT BE USED until the fault has been corrected by a Gas

SafeRegisteredEngineerorinothercountriesaqualiedand

competent Gas Installer.

 Under NO circumstances should any of the sealed components on

this appliance be used incorrectly or tampered with.

 This appliance can be used by children from 8 years and above

and persons with reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children shall not play

with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

 Children should be supervised to ensure that they do not play with

the appliance.

In cases of repeated or continuous shutdown a Gas Safe Registered

Engineer,orinothercountriesaqualiedandcompetentGasInstaller,

should be called to investigate and rectify the condition causing this

and carry out an operational test. Only the manufacturers parts are to

be used for replacement.

FOR ANY QUERIES PLEASE RING THE

MORCO CONSUMER HELPLINE : 01482 325456

NOTE. BOILER RESET PROCEDURE -

To reset boiler, turn mode control knob to reset position and immediately turn knob back to required setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morco GB24 SII Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morco GB24 SII

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info