Bedienungsanleitung Morco GB24 SII (Seite 12 von 36) (Englisch)

646332

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SECTION 4 - gENEral INSTallaTION rEquIrEmENTS

4.1 RECOMMENDATIONS

Current Gas Safety (Installation and Use) Regulation or Rules in

Force.

Theboilerissuitableonlyforinstallationinthespeciedcountries

and should be installed in accordance with the rules in force.

In GB, the installation must be carried out by a Gas Safe

RegisteredEngineer,orinothercountriesaqualiedand

competent Gas Installer. It must be carried out in accordance with

the relevant requirement of the:

• GasSafety(InstallationandUse)Regulations

• AppropriateNationalStandards

• TheWaterFittingsRegulations

• CurrentIEEWiringRegulations

• Health&SafetyDocumentNol.635

• TheElectricityatworkRegulations1989.

• BS5482Part1CodeofPracticeforDomesticbutaneand

propane gas burning installation in permanent dwellings,

residential park homes and commercial premises.

• BSEN1949:2011SpecicationfortheinstallationofLPG

Systems for habitation purposes in leisure accommodation

vehicles and other road vehicles.

IMPORTANT

The manufacturer’s notes MUST NOT be taken, in any way as

overriding statutory obligations.

4.2 BOILER LOCATION

Theboilermustbeinstalledonaatandverticalwall,capableof

adequately supporting the weight of the boiler and any ancillary

equipment.

Theboilermaybettedonacombustiblewallandinsulation

between the wall and the boiler is not necessary unless required

by National Standards.

For Electrical Safety reasons there must be no access available

from the rear of the boiler.

Theboilermustnotbettedoutside.

BATHROOM INSTALLATIONS

This appliance is rated IP20.

The boiler may be installed in any room or internal space, although

particular attention is drawn to the requirements of the current

IEE (BS.7671) Wiring Regulations and the electrical provisions

of the building regulations applicable in Scotland, with respect to

the installation of the boiler in a room or internal space containing

a bath or shower. For IE reference should be made to the current

ETCI rules for electrical installations and I.S. 813:2002.

If the appliance is to be installed in a room containing a bath or

shower then, providing water jets are not going to be used for

cleaning purposes (as in communal baths/showers), the appliance

must be installed beyond Zone 2, as detailed in BS.7671.

0.6m

Zone 0

Recessed

window

Zone 2

Ceiling

3G8913a

2.25m

Zone 1

COMPARTMENT INSTALLATIONS

A compartment used to enclose the boiler should be designed

and constructed specially for this purpose.

An existing cupboard or compartment may be used, provided

thatitismodiedforthepurpose.

• ThepositionselectedforinstallationMUSTallowadequate

space for servicing in front of the boiler.

4.3 FLUE TERMINAL POSITION

Pluming will occur at the terminal so avoid locations where this

will cause a nuisance.

The boiler MUST be installed so that the terminal is exposed to

external air.

It is important that the positions of the terminal allows the free

passage of air accross it at all times.

Minimum acceptable spacing from the terminal to obstructions

andventilationpumparespeciedinthetablebelow.

ForCaravanHolidayHomes;iftheheightoftheueterminal

from any ground, decking or steps is under 1.5m then a suitable

terminalguardshouldbetted.

For Residential Park Homes, please refer to BS 5440 Part 1.

Terminal Guards are available from boiler suppliers.

TFC Flue Guard - Model K6 Round Plastic Coated.

www.tfc-group.co.uk

* Only one reduction down to 25mm is allowable per installation

otherwise BS5440-1 2008 dimensions must be followed.

Flue Terminal Positions

Min. Spacing*

1. Directly below, above or alongside an opening

window, air vent or other ventilation opening. 300mm (12”)

2. Below guttering, drain pipes or soil pipes. 25mm ( 1”)*

BS5440-1 2008 75mm (3”)

3. Below eaves. 25mm (1”)*

BS5440-1 2008 200mm (8”)

4. Below balconies or a car port roof. 25mm (1”)*

BS5440-1 2008 200mm (8”)

5. From vertical drain pipes or soil pipes. 25mm (1”)*

BS5440-1 2008 150mm (6”)

6. From an internal or external corner or to a 25mm (1”)*

boundary along side the terminal. BS5440-1 2008 300mm (12”)

7. Above adjacent ground, roof or balcony level. 300mm (12”)

8. From a surface or a boundary facing the terminal. 600mm (24”)

9. From a terminal facing a terminal. 1,200mm (48”)

10. From an opening in a car port

(e.g. door or window) into dwelling. 1,200mm (48”)

11. Vertically from a terminal on the same wall. 1,500mm (60”)

12. Horizontally from a terminal on the wall. 300mm (12”)

Vertical Terminals

13. Above the roof pitch with roof slope of all angles. 300mm (12”)

 Aboveatroof.  300mm(12”)

14. From a single wall face. 300mm (12”)

From corner walls. 300mm (12”)

15. Below velux window 2000mm (79”)

16. Above or side of velux window 600mm (24”)

Table 4 - Balanced Flue Terminal Position

Morco GB24 SII Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morco GB24 SII

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info