1412: Afterremovingtheouterpackaging,flattenitandlayontothefloorclosetothestove;After removing the outer packaging, flatten it and lay onto the floor close to the stove;
this can then act as protective work surface during the assembly process.
Next, remove the legs from inside the stove. Ca-
refully lift the stove from the wooden pallet and
gently lay the stove onto its back and unscrew the
heat shield from the underside of the stove. Now
screw the legs and the Heat shield into position on
the underside of the base. Following the removal
of the wooden packaging the heat shield must be
fitted to the underside of the stove at the same time
as the legs utilising the same fixing bolts. Please
see drawing.
The stove should now be lifted and moved into
the upright position, avoiding excess load on the
back legs.
1442: Carefully lift the stove from the wooden pallet and set it carefully in place.
1452: The assembly of the soapstone stove 1450 is described separately and instructions are
enclosed with the soapstone packaging.
We recommend that two people perform the assembly and installation procedure. The Morsø
1412 weighs 70 kg, while the Morsø 1442 weighs 80 kg and the 1452 weighs 120 kg.
1.2 Installing the stove
The stove and chimney installations MUST comply to all current National and Local Building Reg-
ulations; your approved Morsø dealer or your local building control officer can advise regarding
this. Ultimately, it is you and your installer who is responsible that the installation complies.
1.3 Chimney sweep
It may also be wise to consult your local chimney sweep before installing the stove. After your
stove has been installed, it is advisable to have the chimney checked and swept at least once
a year. In any case, if your chimney has not been used for some time, it should be inspected
for cracking, bird nests, etc. before it is put back into use.
1.4 Stove placement/clearance requirements
Minimum Clearance requirements apply if the stove is placed near to combustible materials.
Permitted clearances to combustible materials are also indicated on the data plate on the rear
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Morso 1452 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.