Bedienungsanleitung Morso 3116 (Seite 13 von 19) (Englisch, Dänisch)

744385

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

DK ENG

How to position the bae and access bae

Make sure that the upper bae plate (2) is located into

its correct position. It should be placed on top of the rear

(xed) bae section and secured into position against

the 2 upstanding cast lugs. (See diagram).

Note: The access bae (3) must always be tted

when the stove is in use, as it not only assists the

combustion process, but also gives essential pro-

tection to the stove’s top plate.

1.7 Connecting the stove to a masonry chimney

A wall sleeve should be bricked securely into the wall of the chimney at the appropriate height

and the stovepipe inserted centrally. The pipe must not extend into the actual chimney open-

ing, but rather must reach only to the inside of the chimney aperture. The gap between the

stovepipe and sleeve must be sealed using glass bre packing rope.

Only use stovepipe components that comply to National and Local Building Regulations.

1.8 Connecting to a stainless steel insulated chimney system

If your installation involves taking the chimney straight up and through the ceiling, you must

comply with National, Local Building Regulations or ue manufacturers instructions concern-

ing clearances to combustible materials such as walls, oor joists and ceilings. The joint be-

tween the stove ue collar and the stovepipe must also be sealed using glass bre rope. It

is important that the insulated ue system is properly supported both at ceiling level and at

roof level.

THE STOVE MUST NOT BEAR THE WEIGHT OF THE CHIMNEY SYSTEM (See chimney man-

ufacturer’s instructions). Excessive weight on the stove will inhibit expansion and could lead

to damage of the stove top. Damage caused to the stove in this way would not be covered by

the manufacturers guarantee.

In the event that a chimney re occurs resulting from faulty operation or prolonged use of

damp wood fuel, close the air vents completely and contact your local re department im-

mediately.

Be aware of the following:

Cleaning procedure: Discuss this with chimney sweep or qualied installer prior

to or during the stove installation

Chimney draft: If the chimney draft is naturally poor it is better to install the ue from

the top of the stove so as to minimise any internal resistance of the ue gases.

Avoid having any more than 2 bends in the ue system and limit the length of the

oset between bends.

Fresh air supply

A wood-burning stove requires air for combustion. As a result, ring a wood-burn-

ing stove will help create a healthy climate in your house. If the house is very tightly

sealed, and particularly if there is a cooker hood or ventilation system in the house, it

may be necessary to install an air grate in the room in which the wood-burning stove

is installed. Otherwise there may not be enough draught in the chimney, which may

result in the stove not being able to burn properly, and smoke may come out of the

stove when the re door is opened.

If it is necessary to install air grates, they must be positioned so that they cannot

be obstructed.

1.9 Draft conditions

If smoke spillage occurs when the re door is opened, it is probably due to poor chimney

draft. This type of stove requires at least 12 pa of chimney draft to achieve satisfactory com-

bustion and smoke spillage prevention. However, in cases where the stove door is opened

too vigorously you could expect that slight smoke spillage may occur. The ue gas tempera-

ture at the rated output is 218˚ C relative to 20˚ C.

If you have any doubts, you may want to have your installer measure the draft in the chimney.

Draught

The draught in the chimney is the result of the dierence between the high tempera-

ture in the chimney and the cooler temperature outside. Other factors that determine

whether sucient negative pressure can be produced to create a draught include the

length and insulation of the chimney, and wind and weather conditions.

The draught will be reduced when:

- The temperature dierence is too low, e.g. in connection with a poorly insu-

lated chimney.

If the chimney is cold, it may help to light (burn up) a rolled-up newspaper in

the chimney’s cleaning door.

- The outside temperature is too high, e.g. during the summer.

- There is no wind.

- The chimney is not tall enough, with the result that it sits in the lee of the roof

surface or tall trees.

These conditions are also associated with the greatest risk of smoke coming

back down the chimney.

- Air is entering the chimney in undesired places, e.g. through cracked joints or

leaks in the cleaning door or the ue pipe.

- Unsealed, unused replaces are connected to the chimney.

- The ue pipe and chimney are clogged up with soot due to inadequate cleaning.

- The house is too tightly sealed (please see the section on Fresh air supply).

A good draught is achieved when:

- There is a big dierence between the temperature in the chimney and outside,

i.e. when the need for heating is greatest.

- The weather is clear and there is a good wind.

- The chimney is of the proper height, i.e. Minimum 4 metres above the stove,

and clear of the spine of the roof.

Morso 3116 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 3116

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info