Bedienungsanleitung Morso 6140 (Seite 13 von 21) (Englisch, Dänisch)

744334

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

DK ENG

We recommend that the stove be installed at least 10-15 cm from masonry in order to allow

heat to circulate and to facilitate the cleaning of the inside and outside of the stove. A layer

of wallpaper on a brick wall is normally regarded as non-ammable material.

The oor

If the stove is installed on a ammable oor, national and local regulations must be observed

with regard to the size of the non-ammable underlying surface that must cover the oor be-

neath the stove.

The underlying surface must naturally be able to bear the weight of the stove and, if ap-

plicable, the steel chimney.

Distance to furniture

We recommend that the stove be installed 900 mm from furniture, but consideration should

also be given to whether furniture, etc., will dry out as a result of its proximity to the stove.

The distance to ammable material in front of the stove is 900 mm.

A wood-burning stove gets hot when it is red. Caution must therefore be observed, par-

ticularly with regard to children touching the stove.

1.5 The chimney

If local regulations permit, the stove may be connected to a chimney already serving anoth-

er replace (such as an oil-burning stove or another wood-burning stove). Attention should

be paid to any requirements concerning the location of ue pipes if two or more replaces

are connected to the same chimney.

The wood-burning stove must never be connected to a chimney to which a gas-burning stove

is already connected. An ecient, modern stove places great demands on the chimney, so have

a chimney sweep check the condition of your chimney.

The aperture of the chimney must comply with national and local regulations. In general,

the aperture area should measure at least 175 cm2 for wood-burning stoves.

An overly large chimney aperture will mean that too much energy will be required to heat

the chimney suciently to achieve an acceptable draught. If you have a brick chimney with

a large aperture, we recommend that you install an insulating chimney liner of the proper

diameter. This will increase the draught, and improve the fuel economy.

There are no requirements with respect to specic chimney heights, but a chimney must be tall

enough to provide a good draught, and to ensure that the smoke does not cause any problems.

As a general rule, there will be a satisfactory draught if the chimney extends 4 metres above the

stove and at least 100 cm above the spine of the roof. If the chimney is located along the side of

the house, the top of the chimney should never be lower than the spine of the roof or the high-

est point on the roof. Please note that there are often national and local regulations regulating

the location of chimneys in houses with thatched roofs. Please see section 1.9 Draught.

The chimney and the ue pipe must be tted with cleaning doors, which must be at least

the same size as the chimney’s aperture area.

The chimney must be accessible for external inspection, and it must be possible to access

the cleaning doors and the chimney if it is to be cleaned from the top (e.g. steel chimneys).

1.6 Connecting the ue pipe

Lift the upper cast iron top plate o the stove.

Note: The included round cast iron cover plate must be mounted on the upper cast iron top

plate if the stove is being installed with the ue pipe to the rear.

Mounting the ue collar pointing upwards

From the factory, the stove is prepared for installation with the included ue collar (1) pointing

upwards with included ball stop and screws. The ball stop, which prevents the chimney sweep

from damaging the stove’s bae plates while sweeping, is the 145 mm long rod that is provided.

Mounting the ue collar to the rear

If the stove is being installed with the

ue pipe to the rear, the round plate

fixed with two screws on the back

of the stove is dismounted. The iron

piece on the inside convection back

panel is knocked out with light, rm

taps with a hammer next to the small

”bridges” holding the piece.

The cast iron cover is removed from

the back panel and mounted on the

top plate. The ue collar is centred and

screwed onto the back of the stove

with the clamps and screws provided.

The ball stop is not used when install-

ing the ue collar to the rear.

The location of the baes

The baes (2) and (3), which are made

from vermiculite, are mounted at the

factory.

Make sure that the baes are correct-

ly assembled before lighting the stove

(please see the sketch).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 6140 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 6140

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info