Bedienungsanleitung Morso 6170 (Seite 16 von 21) (Englisch, Dänisch)

744338

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

DK ENG

5. Re-stoking should normally be carried out while embers

still remain. Distribute the embers in the bottom, ensuring

that most of them are at the front of the stove.

6. Place 2 pieces of wood of approx. 0.7 kg each and ap-

prox. 25-30 cm long over the embers in a single layer, with

a distance of approx. 1 cm.

7. Open the air supply to maximum and close the door; the

fresh wood will then ignite within a couple of minutes.

8. Reduce the amount of combustion air to the desired po-

sition, and optimal combustion will continue until there are

glowing embers in the bed.

Make sure that there is always enough air (oxygen) to main-

tain clear, lasting ames when, and after, reducing the amount

of combustion air.

During the nominal test, the stoking interval was 60-70 min-

utes.

9. A new portion of wood can be added by repeating steps

5 & 6.

Important!

It is important that the fresh quantity of wood starts

to burn quickly. To ensure the fuel lights quickly, open

the combustion air to max. or leave the door ajar to

allow in the amount of air needed to light the wood.

If, however, the wood only smoulders, there will be a

strong build-up of smoke, which at worst can cause

an explosive ignition of the ue gases with the risk

of material damage and personal injury.

The stove door should normally be opened gently the rst 2-3 cm, then you should wait until

the pressure has equalised before opening the door all the way. This technique will prevent

smoke from getting out, particularly when there is a poor draugt.

The stove door should never be opened when the stove is being red vigorously.

Once the wood has burned out, it becomes glowing charcoall. If a good layer of embers has

already formed on top of a sucient layer of ash, the stove can keep warm for a very long

time, not least due to the favourable qualities of the cast iron.

We would strongly recommend that you do not leave your stove alit at night. It

harms the environment and constitutes very poor use of the wood as the gases

in the wood do not ignite at the low temperature, but settle as soot (unburned

gases) in the chimney and stove. Extreme conditions, such as poor draught in the

chimney, large quantities of wood or wet wood, may in the worst-case scenario

cause an explosive ignition.

When ring in the summer period, when there is minimal need for heat, the combustion

will be poor. The stove provides too much heat so the combustion should be reduced.

But always remember to make sure that there are lasting ames until the wood be-

comes charcoal. If you want a weaker re, stoke up using less wood.

If you re the stove using wet wood, a lot of the fuel’s thermal energy will be spent

forcing the water out of the wood, without releasing any heat to the stove. This

incomplete combustion results in a layer of soot being left in the stove, pipe and

chimney.

Comparison between ring with wood and oil:

Type of wood (moisture content 20%) No. of cubic metres per 1000 litre oil

Oak

Beech

Ash

Sycamore

Birch

Elm

Common spruce

Silver r

7.0

7.2

7.5

8.0

8.9

10.4

10.9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 6170 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 6170

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info