Bedienungsanleitung Morso 6800 series (Seite 18 von 21) (Englisch, Dänisch)

744348

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

DK ENG

5. Lift the upper bae out of its holder and tilt it out.

6. Make sure that the baes and brick panels are correctly

assembled before lighting the stove after cleaning.

4.0 HETAS amendments

Health and safety precautions

Special care must be taken when installing the stove such that the requirements of the Health

and Safety at Work Act are met.

Handling

Adequate facilities must be available for loading, unloading and site handling.

Fire Cement

Some types of re cement are caustic and should not be allowed to come into contact with

the skin. In case of contact wash immediately with plenty of water.

Asbestos

This stove contains no asbestos. If there is a possibility of disturbing any asbestos in the course

of installation then please seek specialist guidance and use appropriate protective equipment.

Metal Parts

When installing or servicing this stove care should be taken to avoid the possibility of per-

sonal injury.

Note of references to the current UK regulations

In all cases the installation must comply with current Building Regulations, Local Authority

Byelaws and other specications or regulations as they aect the installation of the stove.

It should be noted that the Building Regulations requirements may be met by adopting the

relevant recommendations given in British Standards BS 8303, BS EN 15287-1:2007 as an

alternative means to achieve an equivalent level of performance to that obtained following

the guidance given in Approved Document J.

Please note that it is a legal requirement under England and Wales Building Regulations that

the installation of the stove is either carried out under Local Authority Building Control ap-

proval or is installed by a Competent Person registered with a Government approved Com-

petent Persons Scheme. HETAS Ltd operate such a Scheme and a listing of their Registered

Competent Persons can be found on their website at www.hetas.co.uk.

This stove must not be installed into a chimney that serves any other heating appliance.

More detailed advice about existing chimney usage

NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of

the stove to the top of the chimney should be satisfactory. Alternatively the calculation proce-

dure given in EN 13384-1 may be used as the basis for deciding whether a particular chimney

design will provide sucient draught.

The outlet from the chimney should be above the roof of the building in accordance with

the provisions of Building Regulations Approved Document J.

If installation is into an existing chimney then it must be sound and have no cracks or other

faults which might allow fumes into the house. Older properties, especially, may have chim-

ney faults or the cross section may be too large i.e. more than 230 mm x 230 mm. Remedial

action should be taken, if required, seeking expert advice, if necessary. If it is found neces-

sary to line the chimney then a ue liner suitable for solid fuel must be used in accordance

with Building Regulations Approved Document J.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 6800 series Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 6800 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info