Bedienungsanleitung Morso S50-40 (Seite 26 von 36) (Englisch, Dänisch)

744523

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

DK ENG

2.0 Firing/using the stove

Your stove is constructed with air inlets in two places.

Pre-heated, fast-moving combustion air is added to the ﬁre above the glass window, and is reg-

ulated using the handle above the door. The combustion air is let in when the handle is pushed

to the right, and shut off when the handle is pushed to the left.

Another air inlet provides constant, pre-heated air supply which cannot be adjusted, and which

comes into the combustion chamber just above the ﬁre. This helps burn off the last few gasses

emitted by the wood while it is being heated.

The stove’s rated heat output is 8,0 kW.

Your new Morsø stove is EN-tested for ﬁring with wood, and is suitable for intermittent use.

NB!

Wood is a material that contains a great deal of gas (approx. 75%). The gases are released

when the wood is lit and heated. For this reason, it is important that these gases are ignited

quickly after stoking. If the wood just lies smouldering, especially after re-stoking, a lot of

smoke is created which, in the worst case, may cause an explosive ignition of the gases, re-

sulting in damage to the stove.

In order to ignite the gases that are released from the wood, and to keep clear, lasting ﬂa-

mes during the combustion process, it is important to let in the required quantity of oxygen

(air supply) at all times. The setting of the air supply, the method of ignition and the lighting

intervals depend on the draught in the chimney, the wind and weather, the amount of heat

required, the fuel, etc. This means that it may take some time before you get to know the

correct functioning of the stove under any given circumstances.

Although you can ﬁre your Morsø stove with almost all kinds of wood, you should not ﬁre

with wet wood, or unseasoned wood. Wood ought to be stored under a roof for at least 1

year, and preferably 2 years, with free access to wind. Wood should be chopped as soon as

possible after felling if it is to dry quickly. The wood can be used once the moisture is less

than 20%. During the EN test, all stoves are tested with wood with a moisture content of (16

± 4)%.

Never use driftwood as it usually has a high salt content, which damages both the stove and

the chimney. Impregnated and painted wood and chipboard emit poisonous smoke and fu-

mes so they should not be used as fuel either

Please note that liquid fuel may not be used in the stove.

Pieces of wood with a diameter exceeding 10 cm should always be chopped.

The pieces of wood should be short enough to be able to lie ﬂat over the layers of embers,

with air at both ends. The maximum length of fuel in the stove is 30 cm. The maximum qu-

antity of fuel is approx. 2 kg/hour (max. 2 pieces of wood each time you re-stoke).

The ﬁrst few times you light the stove, the ﬁre should be moderate so that the heat-resi-

stant paint can harden before ﬁring more vigorously. During the hardening phase, the paint

may develop obnoxious smoke and smell the ﬁrst time it is lit, which is very normal. Make

sure that the room is well ventilated during this period.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso S50-40 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info