Bedienungsanleitung Motorola Talkabout T82 EXTREME (Seite 9 von 184) (Alle Sprachen)

762156

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

English

and Sub-Code settings from the Leader’s radio. All Members’

radios will remain in this mode for 3 minutes.

• A group with many radios should have all users take this step at the

same time, so all radios can be programmed in one go.

3. On the Leader’s radio, press and hold down the button

until you hear a double beep.

Note:

• At the double beep, this radio’s Channel and Sub-Code settings

will be transmitted, which will be received and copied by all the

other (Members’) radios.

• The Leader’s radio must make this transmission when all the

Members’ radios are still in the Easy Pairing mode, otherwise the

transmission will not be picked up.

• On the Leader’s radio, user must remember NOT to release the

button on the first (single) beep, otherwise this radio will become

another Member’s radio. If that happens, you can press PTT to

escape, and retry the steps described in #3 again.

• If the Leader’s radio is set to a channel between 9 and 16, please

ensure that all Members’ radios have channels 9 to 16 activated.

• When a Member’s radio with only 8 Channels is being Easy-

Paired by a Leader’s radio on Channel 9 or above, Easy-Pairing

will fail, indicated by three short beeps, and “Err” is displayed

briefly.

Internal Voice Operated Transmission/

Voice Operated Transmission ( / )

Transmission is initiated by speaking into the microphone of

the radio/audio accessory instead of pushing the PTT

button.

1. Press Menu until the icon appears on the

display. When audio accessory is connected, the

icon will be shown. The current setting (Off, L1–L3) will

flash.

2. Press or to select the sensitivity level.

3. Press the PTT button to exit menu or Menu to continue

set up.

Note: When using iVOX/VOX, there will be a short delay.

Dual Channel Monitor

Enables you to scan the current channel and another

channel alternately.

To set another channel and start Dual Channel Monitor:

1. Press Menu until the Dual Channel Monitor icon

appears. The Dual Channel Monitor icon will flash.

2. Press or to select the channel then press Menu.

3. Press or to select the Sub-Code.

4. Press the PTT button or wait until time out to activate

Dual Channel Monitor. The screen will alternate between

home channel and Dual Channel Monitor channel.

5. To end Dual Channel Monitor, press Menu.

Note: If you set the same channel and Sub-Code as the current channel,

Dual Channel Monitor does not work.

Silent Mode (Vibrate Alert)

Silent Mode (Vibrate Alert) notifies you that your radio is

receiving a message. This is useful in noisy environments.

The Vibrate Alert will be triggered when you received a call.

It will then only be triggered again if there is no activity within

30 seconds after the previous call.

1. Press Menu until the Vibrate Alert icon is displayed.

The current setting will flash.

L3 = High Sensitivity for quiet environments

L2 = Medium Sensitivity for most environments

L1 = Low Sensitivity for noisy environments

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Motorola Talkabout T82 EXTREME Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info