Bedienungsanleitung Mountfield EL 380 Li 48L (Seite 35 von 42) (Englisch, Italienisch)

765494

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

EN - 8

1. The motor does not

start when the switch is

pressed.

Safety key is not inserted or is inserted

incorrectly.

Insert the key (Fig. 23)

Battery is not inserted or is

inserted incorrectly. Open the hatch and check that the battery

 (Fig. 23)

Low battery. Check the battery status and

recharge if necessary (Fig. 32).

Motor start-up is slow. Press and hold the control lever

for 2-3 seconds (Fig. 25).

The thermal protection has tripped

due to overheating of the motor.

Wait for at least 5 minutes, then

restart the machine.

2. The motor is running but

the blade is stationary.

 

and remove the safety key.

Contact an authorised Technical

Assistance Centre for checks,

replacements or repairs (par. 7.3).

3. The motor shuts down

whilst working.

Battery is not inserted correctly. Open the hatch and check that the battery



Low battery. Check the battery status and

recharge if necessary (Fig. 32).

Obstructions that prevent

rotation of the blade.

Remove the safety key, put on your work

gloves and remove any grass remains or

debris from the lower part of the machine

and/or the discharge channel.

The thermal protection has tripped

due to overheating of the motor.

Wait for at least 5 minutes, then

restart the machine.

Thermal protection has tripped due to

excessive current absorption caused by:

• Excessively high grass cutting.

• Obstructions that prevent

rotation of the blade.

• Too much grass debris accumulated

in the chassis and discharge channel.

•

• Set a higher cutting height when the

grass is very tall, then set a lower

height and cut the lawn again .

• Remove the obstructions (par. 7.2.2).

• Clean the machine (par. 7.2.1)

Wait for at least 5 minutes, then

restart the machine.

4. The cut grass is

not collected in the

grass catcher.

The blade has collided with a foreign





and remove the safety key.

Inspect for damage and contact a Technical

service centre for the replacement of

the blade if necessary (par. 7.3).

The inside of the chassis is dirty. Clean the inside of the chassis to

ease the grass discharge towards

the grass catcher (par. 7.2.2).

5.  The blade is not in good condition Contact a Technical service centre for the

sharpening or replacement of the blade.

6. Excessive noise and/or

vibration is

experienced

whilst working.



the blade is damaged.



and remove the safety key.

Contact an authorised Technical

Assistance Centre for checks,

replacements or repairs (par. 7.3).

7. Battery power

reserve is low.

Severe working conditions requiring

greater current absorption.

Optimise operations (par. 7.1.1).



operating requirements.

Use a second battery or extended

battery (par. 13.2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mountfield EL 380 Li 48L Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info