Bedienungsanleitung Movado Watches (Seite 16 von 72) (Englisch)

757301

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

NOTE: If date is adjusted between 9:00 PM and

12:00 AM when automatic date changes are already

in progress, it should be set to the following day: The

date will not automatically advance at midnight if it has

been corrected via quick mode during these hours.

To set date/time following a battery change:

1. Pull unlocked screw-down crown out to position 2;

watch continues to run.

2. Turn crown clockwise until yesterday’s date appears

in window D.

3. Pull crown out to position 3; watch stops.

4. Turn crown clockwise until today’s date appears in

window D.

5. Continue to turn crown clockwise until hands

indicate correct time.

NOTE: Be sure to take AM/PM into account when

setting time.

6. Push crown back in to position 1, and screw back

down into case.

CHRONOGRAPH FUNCTIONS

Overview

Use buttons A and B to operate the chronograph.

Pressing button A the ﬁrst time will start the

chronograph. Pressing button A a second time will

stop the chronograph, allowing elapsed time to be

read. Pressing button A a third time will restart the

chronograph. Pressing button B will reset chronograph

hands C, E and F to zero. Adjusting the time does not

stop the chronograph, but it does block buttons A and

B for as long as the crown is pulled out.

NOTE: Crown must be in position 1 and hands must

be at zero before chronograph is started. Press button

B to reset hands to zero.

IMPORTANT: Do not push button A or B when crown

is pulled out to position 2 or 3. If button A or B is

accidentally activated while crown is not ﬂush against

case, one or more of the chronograph hands may

become de-synchronized. Should this occur, follow

instructions at end for synchronizing chronograph

hands.

Simple chronograph functions:

To measure the duration of a single, non-stop event:

1. Press button A to start chronograph.

2. Press button A a second time to stop chronograph,

and read the 3 chronograph hands to determine

elapsed time, for example: 1 hour, 8 minutes, 47

seconds.

3. Press button B to reset chronograph hands to zero.

Accumulated time functions:

To measure the combined time of a series of shorter

events, for example the actual playing time of a

football game, where play is repeatedly interrupted:

1. Press button A to start chronograph.

2. Press button A a second time to stop chronograph

and read elapsed time, for example: 15 minutes,

22 seconds.

3. Press button A again to resume measurement.

4. Press button A a fourth time to stop chronograph

again, and read new elapsed time, for example:

28 minutes, 35 seconds.

NOTE: Each time you stop chronograph, chronograph

hands will indicate total accumulated time.

5. Repeat steps 1 and 2 to add each additional

interval of time.

6. After you have taken your ﬁnal accumulated time

reading, press button B to reset chronograph hands

to zero.

7 QUARTZ CHRONOGRAPH

1/1 OF A SECOND – TYPE A

Includes 43.5 mm Movado BOLD and Series 800 Sub-Sea quartz chronographs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Movado Watches Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Movado Watches

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info