Bedienungsanleitung Movado Watches (Seite 19 von 72) (Englisch)

757301

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

CHRONOGRAPH FUNCTIONS

Overview

Use buttons A and B to operate the chronograph.

Pressing button A the ﬁrst time will start the

chronograph. Pressing button A a second time will

stop the chronograph, allowing elapsed time to be

read. Pressing button A a third time will restart the

chronograph. Pressing button B will reset chronograph

hands C, E and F to zero.

IMPORTANT: Crown must be in position 1, screwed

down into case, and counter hands must be at zero

before chronograph is started. Press button B to reset

hands to zero, or, if necessary, reset them following

instructions below.

To reset chronograph counters to zero:

All chronograph hands must be in the zero position

before you start a timing. Unlock crown and follow

these steps as needed to reset the hands of the

counters:

60-Minutes counter:

Pull crown to position 2, press and hold push-button B

and rotate crown clockwise.

30-Seconds counter:

Pull crown to position 3, press and hold push-button A

and rotate crown clockwise.

5-Minutes counter:

Pull crown to position 3, press and hold push-button B

and rotate crown clockwise.

Simple chronograph functions:

To measure the duration of a single, non-stop event:

1. Press button A to start chronograph.

2. Press button A a second time to stop chronograph,

and read the chronograph hands to determine

elapsed time, for example: 5 minutes, 57 seconds.

3. Press button B to reset chronograph hands to zero.

Accumulated time functions:

To measure the combined time of a series of shorter

events, for example the actual playing time of a

football game, where play is repeatedly interrupted:

1. Press button A to start chronograph.

2. Press button A a second time to stop chronograph

and read elapsed time.

3. Press button A again to resume measurement.

4. Press button A a fourth time to stop chronograph

again, and read new elapsed time.

NOTE: Each time you stop chronograph, chronograph

hands will indicate total accumulated time.

5. Repeat steps 1 and 2 to add each additional

interval of time.

6. After you have taken your ﬁnal accumulated time

reading, press button B to reset chronograph hands

to zero.

Split-time or intermediate-time functions:

To take intermediate time readings as a race

progresses:

1. Press button A to start chronograph.

2. Press button B to momentarily stop chronograph.

3. Read off the intermediate time, for example:

6 minutes, 4 seconds.

4. Press button B to resume chronograph function; the

3 chronograph hands will quickly catch up with

ongoing event.

5. To read a second split time, press button B again.

Repeat steps 2 through 4 to take any additional

split times.

6. Press button A to stop chronograph.

7. Take a reading of the ﬁnal time, for example:

25 minutes, 18 seconds.

8. Press button B to reset chronograph hands to zero.

8 QUARTZ CHRONOGRAPH

1/1 OF A SECOND – TYPE B

Includes Series 800 Sub-Sea Retrograde and Verto retrograde chronographs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Movado Watches Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Movado Watches

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info