Bedienungsanleitung MSW PROCAT 800 (Seite 6 von 27) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

779196

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

EN EN

10 11

Rev. 27.02.2017 Rev. 27.02.2017

3 TECHNICAL SPECIFICATION

INSTALLATION AND TEST START-UP

1. Remove hoist from the box and check for any visible damage. Ensure there is no

damage to any of the elements.

2. Make sure all elements are in working order. Also make sure that all nuts are

tightened, then mount device on appropriate load bearing steel profile and con-

nect to the power source.

3. In order to ensure appropriate safety levels, once the electric hoist and the

traverse mechanism are switched on, check the electric power supply source.

The operator should maintain an appropriate distance from the traverse motion

mechanism, and is forbidden to perform test start-ups under that device.

SAFETY GUIDELINES:

1. The device has to be operated by qualified personnel trained within the scope of

the applicable safety rules.

2. Before using the device, the operator has to perform a test start-up without load

and check the following elements:

• Whether the switch permits the load to be lifted, lowered and arrested at any

time.

• Whether the traverse mechanism traverses freely and without obstructions.

• Whether any unusual noises occur during operation of the electric hoist.

• Whether it is possible to coil and uncoil the cable freely.

Model Procat1200 Procat800 Procat500 Procat300

Lifting capacity without pulley/with

pulley 600/990 400/800 250/500 150/300

Lift height (m)

without pulley/with pulley 12/6 12/6 12/6 12/6

Lifting speed (m/min)

without pulley/with pulley 8/4 8/4 10/5 10/5

Hoist motor power (W) 1800 1300 1020 600

Traverse motion motor power (W) 540 540 160 160

Power supply (V/Hz) 230/50 230/50 230/50 230/50

Traverse speed (m/min) 13 13 13 13

Cable diameter (mm) 5.6 5.1 4.2 3

Device weight (kg) 51 36 33 30

3. Lifting loads which exceed the lifting capacity is forbidden.

4. Do not tilt suspended loads and to not drag loads along the ground.

5. Do not use the device outside when it is raining or in unfavourable weather

conditions.

6. People and animals are forbidden to stand or pass under a suspended load (or

near it). Do not lift people or animals using this device.

7. Do not leave a suspended lead unsupervised.

8. Once suspended, balance the weight suspended on the sheave pulley.

9. The limiting switch guarantees safety and protects against overloading the hoist.

10. During operation use the break carefully, so as to prevent the load from drop-

ping. Ensure automatic elements are properly greased. Check the device every

time it is switched on.

11. Do not leave leads suspended on the hook for a long time, as this may damage

the device or cause accidents.

12. Make sure the cable is not too loose. The cable has to be coiled properly to

avoid damage. If the cable is worn out, it should be replaced.

13. Ensure every articulated part is properly greased. Every six months apply grease

to the following elements: hook, cable axis, transmission, bearing, etc.

14. Regularly, usually once a year, carry out maintenance works in order to ensure

the electric hoist remains in good working order.

15. Attention: The motor of this electric hoist works in a S3-20% 10 Min system.

Therefore a work cycle spans 10 Min., where the device is in operation for 2

minutes and then is at rest for 8 minutes. The device may not be used under a

non-stop operation mode.

FREQUENT FAULTS AND REMEDIES

Faults Possible reason Remedy

The motor does not

start after the button is

activated

• No power

• Cabling is cracked or

loose.

• The button is faulty

• The capacitor is

burned out.

• The traverse

mechanism or

traverse buttons do

not work

• Connect power

• Check and repair

cabling.

• Repair or adjust

circuit breaker

• Replace the capacitor

• Check traverse me-

chanism and replace

the traverse circuit

breaker

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MSW PROCAT 800 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info