Bedienungsanleitung MTD 1043 (Seite 13 von 15) (Englisch)

672424

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

English Operating manual

– Always release the throttle and

reduce the engine to no load

when you are not cutting.

– Rotate the unit in the same

direction in which the blade is

cutting. This promotes cutting.

– Move one or two steps to the next

trimming area after swinging back

the unit and stand firmly again.

Follow these instructions to prevent

vegetation from wrapping itself

around the blade:

– Cut at full speed.

– Swing from right to left into

the vegetation which is to be cut

(Fig. 16).

– When swinging back, avoid

vegetation which has just been cut.

Maintenance and

cleaning

`~ìíáçå

_ÉÑçêÉ=ïçêâáåÖ=çå=íÜÉ=ìåáíW

Ó pïáíÅÜ=çÑÑ=íÜÉ=ÉåÖáåÉK

Ó t~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=

ÅçãÉ=íç=ëí~åÇëíáääX=íÜÉ=ÉåÖáåÉ=

ãìëí=Ü~îÉ=ÅççäÉÇ=ÇçïåK

Ó oÉãçîÉ=ëé~êâJéäìÖ=íÉêãáå~ä=Ñêçã=

íÜÉ=ÉåÖáåÉ=íç=éêÉîÉåí=íÜÉ=ÉåÖáåÉ=

Ñêçã=ëí~êíáåÖ=ìåáåíÉåíáçå~ääóK

e~îÉ=~ää=êÉé~áêë=Å~êêáÉÇ=çìí=Äó=

~êÉé~áê=ëÜçé=çåäóK

^í=íÜÉ=ÉåÇ=çÑ=íÜÉ=ëÉ~ëçå=Ü~îÉ=

íÜÉ ìåáí=áåëéÉÅíÉÇ=~åÇ=ëÉêîáÅÉÇ=Äó=

~ ëéÉÅá~äáëí=Åçãé~åóK

aç=åçí=ëéä~ëÜ=íÜÉ=ìåáí=ïáíÜ=ï~íÉêI=

çíÜÉêïáëÉ=ÉäÉÅíêáÅ=ÅçãéçåÉåíë=ã~ó=

ÄÉ=Ç~ã~ÖÉÇK

`äÉ~å=íÜÉ=~ééäá~åÅÉ=~ÑíÉê=ÉîÉêó=ìëÉK=

c~áäìêÉ=íç=ÅäÉ~å=íÜÉ=~ééäá~åÅÉ=Å~å=

Ç~ã~ÖÉ=íÜÉ=ã~íÉêá~äë=~åÇ=Å~ìëÉ=

ã~äÑìåÅíáçåëK

Installing the cutting line

(depending on model)

Always use a replacement cutting

line with a diameter of 3,0 mm.

If using a cutting line which has

a length other than the one indicated,

the engine may overheat or misfire.

There are two methods of replacing

the cutting line:

– Winding a new line onto the spool

– Fitting a coil with a prewound line

Winding a new line onto the spool

Fig. 17

 Press both retaining plates (1)

of the spool housing (2) and

remove the spool together with

spool cover (3).

Fig. 18

 Clean spool housing (1), spring (2)

and spool (3) together with spool

cover (4). Use a clean cloth.

 Check the toothing (5) for wear on

the spool housing (1), the spool (3)

and on the spool cover (4).

If required, replace damaged parts.

 Take approximately 3 metres of

new trim line and fold in half.

Note

Always use the specified line length!

The line may not be released correctly

if it is too long.

Fig. 19



Insert the folded end of the trim line

into the retaining plate of the spool.

 Wind the lines in tight, even layers

onto the lower and upper halves

of the spool. Observe the winding

direction indicated on the spool!

Fig. 20

 Press the ends of the line into the

two opposing retaining slots.

Fig. 21

 Insert the spool into the spool

cover and feed the ends of the line

through the opposing slots in the

spool cover.

Fig. 22

 Press pre-assembled unit (3) out

of the inner spool and spool cover

into the spool housing (2) until the

retaining plates (1) engage.

Fitting a coil with a prewound line

Fig. 17

 Press both retaining plates (1)

of the spool housing (2) and

remove the spool together with

spool cover (3).

 Take spool out of the spool cover.

Fig. 18

 Clean spool housing (1), spring (2)

and spool cover (4). Use a clean

cloth.

 Check the toothing (5) for wear on

the spool housing (1) and on the

spool cover (4). If required,

replace damaged parts.

Fig. 21

 Insert a new spool into the spool

cover and feed the ends of the line

through the opposing slots in the

spool cover.

Fig. 22

 Press pre-assembled unit (3) out

of the inner spool and spool cover

into the spool housing (2) until the

retaining plates (1) engage.

Cleaning the air filter

Clean and lubricate the air filter after

every ten operating hours. This is an

important part of maintenance. If the

air filter is not serviced, the warranty

will be deemed null and void.

Fig. 23

 Set choke lever (1) to position

3/ . The air filter cover can be

removed in this position only.



Open air filter cover: Press retaining

plate (3) and remove cover (2).

 Remove the air filter (4).

Fig. 24

 Wash the filter with detergent

and water. Flush out the filter

thoroughly, leave to drip and

dry completely.

Fig. 25

 Use adequately clean oil (SAE 30)

to lubricate the filter easily.

Fig. 26

 Press on the filter to distribute

the oil and remove excess oil.

 Install filter.

 Attach air filter cover again,

ensuring that it engages.

Note

If the unit is used without the air filter,

the warranty will be voided.

Adjust carburettor

Fig. 27

The idle speed can be set with the

screw (1). This work may be carried

out by a specialist workshop only.

Replace petrol filter

(depending on model)

If required – This work may be carried

out by a specialist workshop only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD 1043 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD 1043

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info