Bedienungsanleitung MTD CubCadet serie 7000 (Seite 45 von 52) (Englisch)

629099

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

• Remove the filter by turning it counterclockwise

using an automotive type filter wrench to

loosen. See Figure 55.

Figure 55

• Reinstall the drain plug in the engine and clean

up any residual oil. Refer to Figure 54.

• Apply a light coating of clean oil on the gasket of

the new oil filter. Thread the filter on by hand

until the gasket contacts the filter base, then

tighten the filter an additional 3/4 turn. Do not

overtighten the filter.

• Refill the crankcase to the "FULL" mark on the

dipstick with the appropriate type oil.

• Reinstall the oil fill cap and dipstick.

• Start the engine and run for about 5 minutes.

Stop the engine and check for leaks at the oil

filter and drain plug.

• Wait 3 minutes and re-check the oil level. If

needed, add oil to bring the oil level up to the

"FULL" mark.

WARNING: Never overfill the engine

crankcase. The engine may overheat

and/or damage may result. For best

results, fill to the “FULL” mark on the

dipstick as opposed to adding a given

quantity of oil. Always check the level

on the dipstick before adding more oil.

Dispose of used oil in an environmentally

safe manner. If necessary, contact your

area EPA office for proper disposal

procedures and recycling center locations.

IMPORTANT:

The oil fill cap and dipstick must

always be installed securely in place when the

engine is running. Severe engine damage could

result from failure to do so.

CHECKING ENGINE COOLANT LEVEL

Before each use, the engine coolant level in the

overflow reservoir should be checked to ensure it is

within the operating range. Engine coolant absorbs

heat from the engine and transfers the heat to the

air flowing through the radiator. If the coolant level

becomes low, the engine may overheat and could

cause severe damage to the engine.

Use a permanent type antifreeze containing corro-

sion and rust inhibitors. Dilute the antifreeze with

water at a 1:1 ratio to mix the coolant solution (50%

antifreeze : 50% water).

NOTE:

Distilled water is recommended for the cool-

ant solution IF your tap water has a high mineral

content. Minerals cause scaling in the engine and

the radiator coolant passages. System efficiency

will be greatly reduced over time and severe engine

damage may result.

• Check the coolant level when the engine is cold

and the tractor is on a level surface.

• Raise the tractor hood and check the coolant

level in the overflow reservoir on the

right

side of

the engine. Refer to Figure 55.

• If the coolant level is below the "LOW" mark,

remove the cap from the reservoir and add

coolant solution to the "FULL" mark.

NOTE:

The cooling system is a closed type.

Normally, to prevent air from entering the system,

the radiator cap should not be removed.

If the overflow reservoir is empty, the radiator cap

should be removed and the coolant level in the

radiator checked before adding coolant to the

reservoir. If necessary, first refill the system through

the radiator filler neck as follows:

WARNING: It is dangerous to remove

the radiator cap when the system is

hot. Allow the system to cool before

removing the radiator cap.

• Turn the radiator cap counterclockwise to the

first stop to release any pressure. Refer to

Figure 50.

• Push downward on the cap and turn counter-

clockwise until the cap stops then lift cap off.

• Slowly pour coolant into the filler neck until the

level reaches the bottom of the filler neck

overflow flange.

• Wait a few minutes to allow as much air as

possible to escape through the filler neck, then

reinstall the radiator cap.

• Fill the overflow reservoir to the "FULL" mark.

OIL

FILTER

FUEL

FILTER

COOLANT

RESERVOIR

FULL

MARK

LOW

MARK

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 7000 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 7000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info