Bedienungsanleitung Mtx audio th800d (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

168710

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installation & Mounting

MTX recommends your new Thunder amplier be installed by an Autho-

rized MTX retailer. Any deviation from specied installation instructions

can cause serious damage to the amplier, speakers and/or vehicles elec-

trical system. Damage caused from improper installation is NOT covered

under warranty. Please verify all connections prior to system turn on !

1. Disconnect the vehicle’s negative battery cable.

2. Determine the mounting place for your MTX THUNDER amplier. Keep in mind there should be sucient air ow for

proper cooling. Mark the mounting holes from the amplier to be drilled. Before drilling make sure all vehicle wires, gas

lines, brake lines and gas tank are clear and will not interfere with installation. Drill the desired holes and mount the MTX

THUNDER amplier.

3. Install a positive (+) power cable from the vehicle’s battery through the rewall using a grommet or rewall bushing to

avoid cable damage from sharp edges of the rewall. Run the cable through the interior of the vehicle and connect it to

the amplier’s +BATT terminal. Do Not connect to the battery at this time.

Note : Use only proper gauge wire for both positive and negative connections.

4. Install a circuit breaker or fuse within 20cm of the battery. This eectively lowers the risk of severe damage to you or

your vehicle in case of a short circuit or accident. Make sure the circuitbreaker is switched o or the fuse is taken out of

the fuse holder untill all connections are made. Now connect your positive power cable to the positive battery terminal

of the battery.

5. Grounding - Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal a bare

metal surface. Attach the ground wire to that contact point. Connect the opposite end of the ground wire to the GND

terminal on the MTX THUNDER amplier.

6. Connect a Remote Turn-on wire from the source unit to the MTX THUNDER amplier’s Remote terminal. If the source

unit does not have a dedicated Remote Turn-on lead, you may connect to the source unit’s Power Antenna lead.

7. Connect RCA cables from the source unit to the MTX THUNDER amplier’s RCA Bi-level inputs. Both low and high

level signals can be used. Run all signal cables away from vehicle wiring, computers and power cables. If cables must

be crossed do so at a 90° angle. Use only high quality twisted pair interconnect cables to decrease radiated noise from

entering the system.

• Using RCA Connections: Simply attach a signal cable from source units RCA outputs to the amp’s RCA inputs. This pro-

vides input signal to the amp.

• Using Speaker Level Connections : If the source unit does not have RCA outputs, high level signals can be used by tak-

ing the supplied high level RCA adapter and connecting it to the vehicle’s rear speaker wiring. Connect the left negative

speaker wire to the green and black striped wire on the high level RCA adapter. Connect the left positive speaker wire to

the solid green wire. Do the same for the right speaker connection using the purple wire. Now plug the RCA connectors

into the amp’s inputs.

8. Connect your speakers to the MTX THUNDER amplier’s speaker terminals using proper gauge wire. The amp has two

PARALLEL speaker terminals, a positive and negative for a single woofer and an optional second set of positive and nega-

tive terminals for a two woofer conguration. The amp can drive a 2 ohm minimum load.

9. Double check all previous installation steps, in particular, wiring and component connections. Once veried, reconnect

the vehicle’s negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.

Note : Gain Levels on the amplier should be turned all the way down (counter clockwise) before proceeding with adjust-

ments.

Troubleshooting

Problem Cause Solution

No LED indication No +12V at remote connection Supply +12V to terminal

No +12V at Power connection Supply +12V to terminal

Insu cient ground connection Verify ground connection

Blown power fuse Replace fuse

Power LED on, no output Volume on source unit o Increase volume on source unit

Speaker connections not made Make speaker connections

Gain control on amplier o Turn up gain

Signal processing units o Apply power to signal processor

All speakers blown Replace speakers

Output distorted Head unit volume set too high Lower head unit volume

Amplier gain set too high Lower amplier gain

Balance reversed Speakers wired L + R reversed Wire speakers with correct orientation

RCA inputs reversed Reverse RCA input

Bass is weak Speakers wired out of phase Wire speakers with correct phase

Not using MTX woofers Buy MTX woofers

Blowing fuses Excessive output levels Lower the volume

Amplier defective Return for service

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mtx audio th800d Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info