Bedienungsanleitung Mtx audio x1000d (Seite 3 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

167884

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

www.mtx.com - www.mtxaudio.eu

4. Input selection switch - This switch, is used to match the ampliﬁer’s input to the source unit’s or DSP unit’s output.

If your source unit or DSP unit has a mono output you can select: Mono L or Mono R as your input connection,

if your source unit or DSP unit has a stereo output you need to select SUM for input now both RCA inputs of the

ampliﬁer are active and the stereo signal will be converted into a mono signal by the ampliﬁer.

5. EBC port - For connecting the included External Bass Control. A remote bass control so the bass can be adjusted

from the driver’s seat.

6. Subsonic ﬁlter control - This control is used to select the desired (high pass) subsonic ﬁlter frequency. The sub-

sonic ﬁlter protects the subwoofer(s) against too low frequencies that can dammage the subwoofer(s).

7. Low pass x-over frequency control - This control is used to select the desired low pass x-over frequency. The

frequency can be adjusted between 40Hz and 200Hz.

8. Speaker Terminals – Be sure to observe speaker polarity through the system. Failing to wire the speakers in

proper phase could result in a loss of bass response and/or poor

overall sound quality.

Caution : The X1000D ampliﬁer is not recommended for loads below 2 ohms.

9. Fuse - For convenience, all MTX XTHUNDER ampliﬁers utilize ATC type fuses. For continued protection in the

event that a fuse blows, replace the fuse only with the same value.

Caution : The power fuse on the amp is for protecting the amp against overdrive. To protect the vehicle’s electrical

system, an additional fuse is required within 30cm of the battery on the 12V+ cable.

10. Power Terminal – This is the main power input for the ampliﬁer and must be connected directly to the positive

terminal of the car battery for the ampliﬁer to operate properly. Use caution when running this cable through the

vehicule. Try to avoid running this cable along side the input RCA cables, antenna cabling, or other sensitive equi-

pment as the large amount of current ﬂowing through this cable can induce noise into your system. It is also very

important to have a tight connection to ensure maximum performance. We recommend to use 10mm2 or larger

power wire with the MTX XTHUNDER X1000D ampliﬁer.

11. Remote Terminal – The Ampliﬁer can be turned on by applying 12 volts to this terminal. Typically this voltage is

supplied by a wire from the source unit marked “remote” or “electric antenna”.

12. Ground Terminal – A good quality ground is required for your Ampliﬁer to operate at peak performance. A short

length of cable the same gauge as your power cable should be used to attach the ground terminal directly to the

chassis of the vehicle. Always scrape or sand any painted surfaces to expose bare metal where the ground wire

will attach.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mtx audio x1000d Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info