DANGER! Danger of life / risk of fire and electric shock!
Installation and assembly of electrical equipment must be carried out only by a skilled person!
Power supply:
Via DCF terminals of the time switch / master cklock
(without battery, rechargeable battery)
Output:
DCF telegram
Connect the radio receiver only to the DCF terminalsof the time switch / master clock!
Warranty void if housing opened by unauthorised person!
The electronic circuit is protected against a wide range of external influences.
Incorrect operating may occur if external influences exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with local building and electrical codes!
Receiver:
Narrowband-heterodyne receiver
Operation indicator:
Flashing LED on receiving
Consequence of an interference with
reception:
Time switches / master clocks use their quartz as time base
Antenna:
Built-in ferrite rod
Installation note
Permitted ambient temperature:
–20 °C…+50 °C
A
fter the radio receiver has been connected, it may take up to 60 seconds for the LED on the underside of the device to
start to flash!
The LED that is visible through the underside of the radio receiver must flash at one-second intervals. If the flashing
frequency is irregular or interrupted by flickering, this indicates no radio reception is possible and a different location
should be selected for the radio receiver!
Housing:
Self-extinguishing thermoplastic
Mounting:
Wall mounting with fastening bracket
Type of protection:
IP 54 toDIN EN 60529
Recommended cable(s):
Shielded/cross section 0.33 to 2.5 mm
2
Type of connection:
Electrical power supply / protocol via 2-wire connection of the
DCF terminals of the time switches and master clocks
Connection of time switches / master clocks
Cables and cable routing
Wall mounting
IMPORTANT NOTE:Connect the radio receiver only to the DCF terminals of the
time switch / master clock!
Connect the radio receiver and time switch together so the
line(s) does/do not run between the installation wall and the
radio receiver.
Max. cable length: 200 m
Cable diameter: 0.33 to 2.5 mm2
Avoid routing in parallel with other lines (electricity, phone, etc.)
Unscrew both screws on the underside of the housing and lift off the base plate.
Guide a 2-core cable with any cross section through the supplied cable grommet, and install in
the opening of the base plate.
Screw the cable tight with the terminal.
Screw the housing back onto the base plate.
Select a favourable location (see also "Location and installation, in the building or outdoors").
Screw the fastening bracket on the wall and connect the radioreceiver.
Location and installation, in the building or outdoors
Drilling template for wall bracket
No transformers, relays, contactors or the like are allowed to be
installed within a radius of 1 m around the radio receiver. If
there is a fluorescent lamp in this vicinity, it is necessary to
guarantee that it will be turned off from time to time, in order
ensure that a correct reception is possible during the switching
-
off time.
The transmitter is located in the vicinity of Frankfurt/Main. The
most favourable reception possibility is provided if the printed
front surface of the receiver is facing towards Frankfurt/Main. If
the LED that can be seen through the underside of the radio
receiver is flashing every second, this means the reception is
correct.
If wall mounting is used, the wall should not have any electrical
cables and metallic objects that disrupt reception.
The radio receiver is not allowed to be installed in a switch
cabinet or in the immediate vicinity of one.
After the radio receiver has been connected to a time switch, it
may take up to 60 seconds for the LED on the underside of the
radio receiver device to start to flash.
(DRAWING NOT TO SCALE)
Display on time switches with radio reception
When the radio receiver is connected, the time switches indicate with flashing of the DCF symbol that a connection has been established. It can take up
to 60 seconds for the symbol to appear on the display of the time switch after the radio receiver has been connected.
The symbol on the display flashes for between 2 and 3 minutes. Following this, the symbol remains continuously on the display, and signals that
synchronizationhas been successful.
If the DCF aerial does not receive ANY signal, the switching computers continue running internally with quartz accuracy. The DCF symbol is NOT
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Muller FU 20.00 pro wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
