Bedienungsanleitung Muller GS 40.00 mod (Seite 2 von 2) (Deutsch, Englisch)

683976

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

_______________________________________________________________________________________________________________________________________________________ BA GSxx00mod TSxx00mod Hardware N; de, en -23876- 2018.09.V01 ED

INSTRUCTION MANUAL AIR QUALITY SENSORS GS 4X.00 MOD / GS 3X.00 MOD / TS 3X.00 MOD HUGO MÜLLER GMBH & CO KG, STURMBÜHLSTR. 145-149, 78054 VS-SCHWENNINGEN

SAFETY INSTRUCTIONS AND BASICS

40.00 mod / GS 30.00 mod /

TS 30.00 mod

Technical data

Safety instructions / Intended use

Power supply:

Bus current:

12-40 V DC

< 20 mA

CAUTION!

DANGER OF FIRE AND ELECTRIC SHOCK!

!!!Installation and assembly of electrical equipment must be carried out only by a skilled person!!!

Protocol / Interface:

Modbus ASCII, Modbus RTU / RS 485

Connect only to suitable supply voltage [12-40 V DC].

Warranty void if housing opened by unauthorized person!

The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if external influences exceed certain limits!

Installation and assembly of electrical equipment must be in accordance with national building, electrical and safety codes!

Defective devices / sensors have to be put out of service immediately!

Observe the regulations and instructions in the ZVEI/ZVEH handbook (building system technology). Especially the professional installation of the bus lines and the

professional instal

lation and start-up of KNX devices must be observed!

The device fits for the particular use of the following tasks: monitoring of the air quality in building systems technology (schools, offices, hotels, conference venue

etc.), data transfer and regula

tion via bus system.

The device is intended for use in accordance with the defined technical data.

Operate the device exclusively in a dry room!

The device is not qualified for security relevant tasks such as emergency doors, fire protection equipment, fermenting cellars etc.

Baud rates:

4800, 9600, 19200 (Default), 38400

Parity settings available:

None, even, odd

Sensors (depending on model):

, relative humidity, temperature,

atmospheric pressure

Measuring range CO2 concentration:

390–10.000 ppm (GS 4x only)

Measuring range relative humidity:

0–100% (GS 4x, GS 3x only)

Measuring range temperature:

0–50°C

Measuring range atmospheric pressure:

absolute atmospheric pressure (GS 4x, GS 3x only)

Permitted ambient temperature :

-0°…+50°C

Housing:

self-extinguishing thermoplastic

Mounting:

Wall

Type of connection :

Push-in connector

Type of protection :

IP 20 to DIN EN 60529

Class of protection:

III when installed according to regulations

Source of interference

Inappropriate use / disposal

Device configuration (example)

The measurement results of the device can be

negatively influenced by external factors. Possible

sources of interference are:

■ Draught and air movement: e.g. through windows,

doors, convection, heating and people

■ Warming and cooling: e.g. sunlight or mounting on

an outside wall

■ Heat sources: close to installed electrical

consumers

e.g. dimmers

■ Vibrations or shocks, which the unites are or were

subjected to

■ Pollution due to colors, wallpaper paste, dust e.g. at

renovation work

■ Organic solvents or their vapours: e.g. detergents

■ Plasticizers from stickers and packaging: e.g. bubble

wrap or polystyrene



The device is not intended for use of unauthorized constructional alterations, repairs and

security relevant tasks



The device is not intended for use in outdoor areas and wet rooms



The device is not qualified for security relevant tasks The controlling of the device is only

for the observation and regulation of the air quality



The inappropriate use of the device can cause damage to property and persons



The device has to be disposed in an environmentally friendly manner according to the

current electrical codes!

ASSEMBLY

Assembly

Disconnect device from power supply for wiring and installation

purposes! Check power supply is disconnected!

Attention! You have to check and consider the safety instructions above!

 This device is suitable for wall mounting or for mounting on a flush-mounting

box.

 The device should not be exposed to dusty environment.

 Ensure that no dust get inside of this device.

 After initial startup, the device requires up to 5 minutes until the first correct

measurement is possible

STEP 1: Open the device at the bottom and remove the front cover.

STEP 2: Mount the rear cover to the wall or on a flush-mounting box

STEP 3: Connect the RS 485 Modbus serial cable and configure device according to the

project definition (address, baud rate…). Afterwards connect the power supply

STEP 4: After completing the installation the front cover must be reattached

Installation note: Make sure that no wires are pinched or squeezed when installing the cover. The mounting of the device on a flush-mounting box is recommended for easier handling and wiring.

Power / Status LED: Green: In operation / Power on

Flashing green: False / faulty configuration (DIP-switches)

Red: Active bus communication

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Muller GS 40.00 mod Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info