Bedienungsanleitung Muller GS 41.10 knx (Seite 2 von 2) (Deutsch, Englisch)

683947

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

BA GS4x10knx Hardware HM;DE,GB -23769- 2017.11V04 ED.doc

INSTRUCTION MANUAL AIR QUALITY SENSORS GS 4X.10 KNX

HUGO MÜLLER GMBH & CO KG, STURMBÜHLSTR. 145-149, 78054 VS-SC

HWENNINGEN

SAFETY INSTRUCTIONS AND BASICS

GS 40.10 knx

GS 41.10 knx

Technical data

Safety instructions / Intended use

Power supply:

Bus current:

Via KNX bus voltage

< 10 mA

CAUTION! DANGER OF FIRE AND ELECTRIC SHOCK!

!!!Installation and assembly of electrical equipment must be carried out only by a skilled person!!!

Bus system:

KNX

Connect only to suitable supply voltage [KNX bus voltage (nominal voltage 29V)].

Warranty void if housing opened by unauthorized person!

The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if external influences

exceed certain limits!

Installation and assembly of electrical equipment must be in accordance with national building, electrical and safety codes!

Defective devices / sensors have to be put out of service immediately!

Observe the regulations and instructions in the ZVEI/ZVEH handbook (building system technology). Especially the professional

installation of the bus lines and the professional installation and start-up of KNX devices must be observed!

The device fits for the particular use of the following tasks: monitoring of the air quality in building systems technology (schools,

offices, hotels, conference venue etc.), data transfer and regulation via bus system.

The device is intended for use in accordance with the defined technical data.

Operate the device exclusively in a dry room!

The device is not qualified for security relevant tasks such as emergency doors, fire protection equipment, fermenting cellars etc.

Sensors:

, relative humidity, temperature,

atmospheric pressure

Manual operation (GS 41.10 knx):

Manual adjustment of set-point temperature

±3° (increment 0.5°)

Measuring range CO2 concentration:

390–10.000 ppm

Measuring range relative humidity:

0–100%

Measuring range temperature:

0–50°C

Measuring range atmospheric pressure:

absolute atmospheric pressure

Permitted ambient temperature:

-0°…+50°C

Housing:

self-extinguishing thermoplastic

Mounting:

Wall

Type of connection:

Push-in connector

Type of protection:

IP 20 to DIN EN 60529

Class of protection:

III when installed according to regulations

Source of interference

Inappropriate use / disposal

Operation of GS 41.10 knx

The measurement results of the device can

be negatively influenced by external factors.

Possible sources of interference are:

■ Draught and air movement: e.g. through

windows, doors, convection, heating and

people

■ Warming and cooling: e.g. sunlight or

mounting on an outside wall

■ Heat sources: close to installed electrical

consumers e.g. dimmers

■ Vibrations or shocks, which the unites are

or were subjected to

■ Pollution due to colors, wallpaper paste,

dust e.g. at renovation work

■ Organic solvents or their vapours: e.g.

detergents

■ Plasticizers from stickers and packaging:

e.g. bubble wrap or polystyrene



The device is not intended for use of unauthorized constructional

alterations, repairs and security relevant tasks



The device is not intended for use in outdoor areas and wet rooms



The device is not qualified for security relevant tasks The controlling of

the device is only for the observation and regulation of the air quality



The inappropriate use of the device can cause damage to property and

persons



The device has to be disposed in an environmentally friendly manner

according to the current electrical codes!

Set-point temperature

manually adjustable

via touch-area

(adjustment range

±3°; increment 0.5°).

Display with LEDs.

ASSEMBLY

Assembly

Disconnect device from power supply for wiring and installation

purposes! Check power supply is disconnected!

Attention! You have to check and consider the safety instructions above!

 This device is suitable for wall mounting or for mounting on a flush-mounting box.

 The device should not be exposed to dusty environment.

 Ensure that no dust gets inside of the device.

 After initial startup, the device requires up to 5 minutes until the first correct

measurement is possible

STEP 1: Open the device with a small screw driver by pushing in the

lever at the bottom of the housing and gently remove the front cover.

STEP 2: Fix the rear cover, either directly to the wall or on a flush-mounting box

(see installation notes)

STEP 3: After wiring, press the “learn button” to set the device into programming

mode (this can be done at a later time as well)

STEP 4: After completing the installation, the front cover must be reattached

Installation note: Make sure that no wires are pinched or squeezed when installing the cover. The mounting of the device on a flush-mounting box is recommended for easier handling and wiring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Muller GS 41.10 knx Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Muller GS 41.10 knx

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info