Bedienungsanleitung Multiplex EUROPAmc (Seite 12 von 32) (Englisch)

30222

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

The

function

"now

more,

now less"

The

Dual Rates

function

(DR

for

short)

makes it

possible

set up a

servo

with

two

different travels,

and switch

between

them at

will Large

control

surface

travels are

required

whenever the

model is

required to

respond

qurckly

and

powerfully.

Reduced travels

give you

more sensi-

tive

control,

which can

help to

produce

smoother

manoeuvres

The

EUROPA

mc is

preDared

for Dual Rates on

channels

and

2. DR

is switched

on and off separately

for

each

channel.

The DR switches

are

optional,

and

have to be

fitted

the user.

lnstalling

and connecting

Dual

Rates switches

Please use

either of the

MULTIPLEX

two-position

switches

listed

below:

Order

No. 7 5742

(short

toggle)

Order

No.

5743

(long

toggle).

'|,

open

the transmitter

case

(see

illustration).

Remove the charge

socket cap betore

you

remove the two

lalches.

2. Cut away

the

film

over

the switch

position

you

wish to use'

You can use any

of the eight

switch

wells on either side

of the

display.

Install the

switch or switches

and

tighten the

securing

nut.

connect

the

switches

The sticker

inside the transmitler

shows

where the

switches

are

plugged

in.

Channel

connector

Channel

connector

Check

that the

plug

engages

on all three

contacl

pins

on the

transmitter

circuit board.

the

switch operates

the

wrong direction

(it

matter of

preference)

simply

turn the

plug

through

degrees.

5. Close

the

transmitter

case.

Setting

Dual Rates

travels

The

"normal"

control surface

travel

is set up

in the

point

SEflyO'

where

you

can

adjust both

sides separately.

Make these adjustments

first, so that

your

servos

work correctly

under

normal circumstances.

When

you

adjust

servo travel

under the

point

MN, the altered

travel applies

both sides

of neutral equally.

Example:

Normal travel:

left 40 degrees,

right 30 degrees

DR travel

reduction set to

half:

travel

left 20 degrees,

right 15 degrees

To set

DR travel

we will start

from the Status

display again.

1. Select the

point

MN, but do

not activate

Press the

+ button three

times.

The menu

point

is now selected'

but

nol

yet

activated.

2. Select

the

channel

using

QUICK-SELECT

Move the

stick corresponding

the channel

you

wish to adjust

(channels

2 only). QUICK-SELECT

leads

you

directly

servo

travel adjustment.

You cannot

move to this

adjustment

tacility using

the +/-

buttons.

Move DR switch

to the ON

Position

only

active

when both arrows

appear

in the display,

and

you

can

then set

the

reduced travel using

the

+/-

buttons.

Remove

latches

ill

transminer

Cut outtiln

Fig.9:

Prcpareopening

for switches

Fig.10:

Connecting

DR switches

t10

TGnsmitterelect@nics

EEIE

l(t"1".1,,

DR channel2

llz

s a

rl@t

s a

DR is ON

Manual EUBOPA

G8.12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex EUROPAmc Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex EUROPAmc

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info