Bedienungsanleitung Multiplex Mini Mag 21 4211 (Seite 33 von 56) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

561568

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Do not connect the flight battery to the speed controller

until you have switched on the transmitter and move

the throttle stick or switch to the “Motor Stopped”

position.

Switch on the transmitter, connect the flight battery to the

speed controller, and the controller to the receiver. With

this model you must use a controller with what is known

as a BEC circuit (receiver power supply from the flight

battery).

Now switch the motor on briefly, and check once more the

direction of rotation of the propeller. Hold the model firmly

when you run the motor, and remove any loose lightweight

objects from the area behind the model before the propeller

does the job for you.

Caution: even small motors and propellers represent

a distinct injury hazard!

27. Setting the control surface travels

It is important to set the control surface travels correctly,

as these settings have a crucial influence on the model’s

overall control response. In all cases the travels are

measured at the point of maximum chord (width of control

surface.

Elevator

up - stick back - approx. + 11 mm

down - stick forward - approx. - 11 mm

Rudder

left and right - approx. 6-10 mm

each way

Ailerons

up - approx. + 7 mm

down - approx. - 3 mm

MagicMixer #1 (optional) # 7 3000

The MagicMixer #1 permits the use of a simple radio control

transmitter without mixer functions. It is adequate for:

MINI MAG 3-channel RC transmitter

Without the MagicMixer #1 you will need at least a four-

channel computer transmitter with mixer functions.

Using this module the Mini Mag can be flown even with a

transmitter such as the Ranger III, as supplied with the

EasyStar and SpaceScooter RTF models.

It provides a means of controlling

two aileron servos and

the rudder from a single channel (right / left output) at the

receiver.

The servos, and therefore the control surface travels, are

automatically actuated with the correct deflections. Using

the MagicMixer #1 the degree to which the rudder follows

the ailerons (“combi-switch” / CAR function) and the aileron

differential are fixed, i.e. they cannot be altered.

Aileron differential means that the up-aileron travel is greater

than the down-aileron travel. This helps to prevent the model

swinging away from the turn (adverse yaw) when ailerons

are applied.

If you are using the MagicMixer #1 your transmitter must

offer at least the following channels:

Channel 1: Ailerons, coupled rudder (3 servos)

Channel 2: Elevator (1 servo)

Channel 3: Throttle (1 servo)

Connect the aileron servo leads as described in the

“MagicMixer #1” instructions. Take care to maintain

correct polarity when making these connections: the signal

pin is indicated on the label of the MagicMixer with the

square signal symbol. The signal wire in the servo lead is

generally yellow or orange.

Connections at the MagicMixer #1:

r/l = to receiver, right / left output

AR = to right aileron servo

AL = to left aileron servo

R = to rudder servo

If necessary, set the correct direction of servo travel using

the servo reverse facility on your transmitter.

Y-lead for the aileron servos (optional) # 8 5030

The Y-lead permits the use of a simple four-channel radio

control transmitter, i.e. without mixer functions. The two

aileron servos are actuated simultaneously by a single

receiver servo output.

Please note: in this case the differential aileron movement

must be obtained by mechanical means. This is achieved

by offsetting the servo output arms forward by two splines.

This must be done before you install the servos. The rudder

is controlled via a separate channel with this arrangement.

Computer radio control transmitter

If you have this type of transmitter you need neither a

MagicMixer #1 nor a Y-lead.

The transmitter must feature the following adjustment

facilities:

- Aileron differential mixer

- Servo reverse

- Servo travel adjustment

- Optional combi-switch (coupled rudder / ailerons)

Note: when you apply a right-aileron command at the

transmitter, the right-hand aileron (as seen from the

tail) must deflect up.

If you find that you cannot set the correct control

surface travels with your radio control system, you

will need to change the linkage hole to which the

pushrod is connected.

28. Gilding the lily

The kit includes a multi-colour decal sheet. Cut out the

individual name placards and emblems and apply them to

the model, either following our scheme (kit box illustration)

or using your own arrangement. If you have built the rudder

/ elevator version of the model, you will find decals on the

sheet designed for covering the servo recesses in the wing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Mini Mag 21 4211 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info