Bedienungsanleitung Multiplex Power Peak A4 EQ-LCD - 30 8560 (Seite 13 von 48) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

628913

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Table of contents

Power Peak® A4 EQ-LCD

6. Selecting the Charging Current

The charging current must be set first before

charging the battery. To do so, set the charging

current for the battery (300...3,000mA) with the

rotary knob on the front of the charger.

1C means capacity value = charging current.

• Example: LiPo/NiMH cell at 1500 mAh;

1C = 1500 mA (= 1.5A) charging current

This is the correct charging current for the most

commonly used types of lithium/NiMH battery.

Higher capacity battery packs can, of course,

also be charged. In this case, the required charg-

ing time will increase accordingly.

Certain batteries can be charged at a higher or

lower charging rate than 1C. Pay attention to the

information provided by the battery manufac-

turer!

Charging time at 1C: LiPo approx. 1.5 h, NiMH

approx. 1h

7. Charging LiPo Batteries

A lithium battery pack must be charged with

the voltage sensor lead connected. Exception: 1

LiPo cell.

• Ensure the polarity and position are correct

when connecting the voltage sensor lead.

The black wire of the sensor lead must be

aligned with the arrow mark on the charger

casing.

• Ensuring correct polarity, now connect the

main power cables of the battery to the con-

nection at the charger (red = +/black = -).

• Start the charging operation by pressing

and holding the Start button. The battery

voltage is checked and the number of cells

determined in the first 10 seconds. The

charging process can be stopped at any

time by pressing the Start button again.

• While charging the LiPo battery, the total

voltage, charging current and charged

capacity are shown alternately in the LC

display.

• The battery is equalised during the char-

ging process.

The equalizer LEDs indicate the status of the

connected cells. Constantly flashing or lit LEDs

indicate that the cells are being balanced. The

LEDs only flashing sporadically or off indicate

that the battery is balanced and is ready for use.

The lithium battery pack is charged with a con-

stant charging current until the end of charge

voltage of 4.2V per cell (B) is reached. The volt-

age is then kept constant and the remainder of

the charging process takes place in the form of a

descending power curve (C) down to the switch-

off point (D). Charging current = C/10. The end

of charge is signalled by the status LED chang-

ing colour to orange and the beeper sounding.

The battery can now be disconnected from the

charger and used.

7.1 Explanation of LED Flash Sequences

LiPo charging mode

Battery status Status LED

1 No charging

LED and battery type

flash green at 0.5 sec

intervals

Charging started

or checking battery

voltage (A)

LED constantly lights

green for approx. 10 sec

Charging range

(A-C)

LED flashes green

with number of cells

Charging, battery

95 % charged (C-D)

LED flashes orange

with number of cells

Battery charged

(D)

Beeper sounds

for 15 sec

LED flashes orange

with number of cells

# 30 8560

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Power Peak A4 EQ-LCD - 30 8560 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info