30232
10
Zoom out
Zoom in
Vorherige Seite
1/23
Nächste Seite
27
6. The STEERING LL
The PROFI CAR offers the following facilities for setting up the steering function:
Servo norm, centre and travel right/left (èè 6.1)
These settings are used to adjust the servo to match your car’s mechanical
system, and at the same time determine the maximum steering travel and the
centre setting for straight running.
Steering MINTRA (MINimum TRAvel) (èè 6.2)
You can adjust the steering travel using the digi-adjustor while you are running
the car. This enables you to fine-tune the steering response to suit changing
course conditions or vehicle characteristics (e.g. tyre temperature). This menu
point allows you to define the smallest steering travel which you can set by
rotating the digi-adjustor. MINTRA avoids the danger of suddenly having no
steering control if you turn the adjustor too far by mistake. The smallest value
you can set is 30%.
EXPO (èè 6.3
By applying EXPOnential to the steering function, you can make the steering
response of your car more or less sensitive around the centre position.
Steering travel and trim increment (èè 6.4)
(„T“ menu, menu point „TRIM“)
The effect of trim rocker A (steering centre point) and the digi-adjustor (steering
travel) can be set to FINE (1% increments), MEDIUM (2% increments) or COARSE
(4% increments). The selected setting also applies to all other trim rockers.
6.1. Adjusting the steering servo
The first step is to set the signal norm and the direction of rotation for the servo,
followed by the settings for left (LL), straight ahead () and right (ŒŒ). These basic
settings ensure that servo 1 (steering servo) is set up correctly to suit the
characteristics of your model.
The drawing on the right shows an example of
the settings available in the “S-TRA” menu. The
stated angles (0°/45°) show what the servo “can
do”. The adjustments points LL“ and „ŒŒ define
the maximum travel set for the steering servo.
To adjust either of these points you must turn
the steering wheel in the corresponding
direction. At the point you determine the servo setting for “straight ahead”.
The S-NORM” menu point is used to select the signal format (MULTIPLEX or
UNIVERSAL) and direction of rotation for the servo. “MULTIPLEX norm” means that
the pulse width for the centre position is 1.6 ms, and the full range is +/- 0.55 ms.
UNIVERSAL servos operate on 1.5 ms +/- 0.5 ms. If the selected signal format does not
match your servo, the centre position and travels will not be correct.
The “S-TRAV” menu point is used to set the centre position and steering travels for
right and left.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Multiplex PROFIcar301 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Multiplex PROFIcar301

Multiplex PROFIcar301 Bedienungsanleitung - Deutsch - 23 seiten

Multiplex PROFIcar301 Bedienungsanleitung - Französisch - 23 seiten

Multiplex PROFIcar301 Bedienungsanleitung - Spanisch - 23 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info