Bedienungsanleitung Multiplex PROFImc3010 (Seite 8 von 79) (Englisch)

30252

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

Changing the

RF module;

changing crystals

Grasp the

module

the recessed

points (Fig.

7), then

oull

uo and

out of its holder.

The crystal is

plugged

into the side of the

RF module

(Fig.

8). Pull out the crystal by its

plastic

tag.

When

plugging

in a crystal make sure that both

pins

engage

correctly

the socket

the

module.

Before

plugging

the module in

again,

bend the

plastic

tag over to one side.

When

relitting the module

not

press

down

in the

centre

of the

unit,

but

around

the finger recess

position.

This will help to ensure that

it is fitted

squarely,

thereby

avoiding damage to the contacts.

Ftg.7

Transmitter back

panel

lnside

both sides there are holders for a spare

pair

of crys-

tals

and

a replacement fuse. Please note the specially

formed

holder for

double superhet

receiver

crystals

and

their correct

position

the

holder

(Fig.

9).

Don't lever them out

slide them!

Outside

There is a well in the outside of the back

panel

which ac-

commodates

the transmitter aerial Ior transport. The sup-

port

bar can be set

to three ditferent

positions:

folded in

flush, at right-angles to

form

a back support, and upright

as a carrying

handle. Please refer to

Figs. 10

12.

Fig. 11

Fil.12

lnside the

transmitter

Fuse

Take a

look

Fig. 13. The basic

purpose

the fuse is

protect

the

transmitter against excessive currents

during

rapid charging.

lf the fuse burns out, replace

with the same

type

x 21mm,2 Ampere,

quick-actjng

standard

commercial item). Charge currents

higher

than

2A may cause damage

to the transmitter electron-

ics!

Cable compartment

The leads from

the various switches are stowed away

inside

the

cable

compartment

(Fig.

14).

To open the compartment

push

one of the spring

latches to one side

and lift the cover off.

Pass the

wires from each connector

into the comparl

ment through the

nearest opening. Lead them out again

through

the openings on the side

nearest the RF

mod-

ule.

Part of the

"excess"

cable length can be accommo-

dated

inside the compartment.

Any spare cable

is best

left at the switch

position.

Always arrange

the wires carefully and

neatly, to

avoid

the cables

forming a mass of unruly

"spaghetti"

around

the stick units

or close to

the keypad cover well.

Fig. 13 Fig.

The connectors

Three

sides

of the main electronics circuit

board

are

ex-

posed,

each fitted

with

connectors

for the

"peripherals",

i.e.

stick units,

switches and so on. See

Fig. 15.

Starting

from the

lefl,

these are:

Digi-Adjustor. lf

you plug

this

the

"wrong"

way round,

the

and

unctions

will be reversed.

MNT MULTINAUT

(module

no longer available)

KnR

Right-hand stick unit.

Control

"E".

This is normally

the left-hand slider control.

Fig.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex PROFImc3010 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex PROFImc3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info