Bedienungsanleitung Multiplex ROYALevo7 (Seite 72 von 77) (Englisch)

30268

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

ROYAL evo 7 - Instructions

Page 71

ENGLIS

21. Error messages

Every time you switch the transmitter on, the

ROYALevo7 checks the contents of its memory. If it de-

tects an error, the following error message will appear:

Memory Error

If this should happen, do not use the transmitter, and

do not make changes to any settings.

The ROYALevo DataManager PC back-up and update

program (Î 23.1.) is capable of correcting many data

errors. To make use of this simply carry out a data back-

up procedure. The data error will be recognised by the

ROYALevo Data Manager:

If you confirm by clicking on “Yes”, but the error mes-

sage occurs repeatedly, there is a serious data error. In

this case the cause is often a hardware defect (perhaps

caused by neglecting the battery charging instructions,

or using an unsuitable or faulty charger). The trans-

mitter must then be sent to a MULTIPLEX Service Centre

for checking and repair.

Important: please check the version of ROYALevo

DataManager you are using.

For the ROYALevo 7 a later version of the ROYALevo-

DataManager is required than is current at the time of

printing of these instructions (V1.06).

22. Accessories

22.1. HFM-4 crystal RF module

# 4 5690 35 MHz A- and B-band

# 4 5691 40/41 MHz band

# 4 5697 36 MHz

#4 5692 72 MHz

Reasonably priced RF modules using conventional crys-

tal technology. Be sure to use genuine MULTIPLEX plug-

in crystals.

Important: which channels can be used?

Regulations concerning the use of radio-controlled

models vary from country to country. Please make en-

quiries to establish which RF module you should use,

and which channels are approved for the region in

which you wish to fly your models.

22.2. Channel-Check module for HFM-4

crystal RF module

# 7 5164 35MHz A- and B-band (also for 36MHz)

# 7 5165 40/41MHz band

The Channel-Check module is simply plugged into the

HFM-4 crystal RF module, and is easy to

install at any time. The Channel-Check

module requires a receiver crystal (MUL-

TIPLEX single-conversion crystal) whose

channel / frequency is the same as the

transmitter crystal you are using. When

you switch the transmitter on, the mod-

ule checks whether the transmission

channel is in use, and only switches the

RF module on if it is vacant. In this way it

guards against frequency clashes and makes an impor-

tant contribution to safety in model sport.

Retro-fitting the module

1. Switch off and open the transmitter

2. Remove the HFM-4 RF module

3. Plug the receiver crystal into the

Channel-Check module

4. Plug the Channel-Check module

into the RF module

5. Re-install the RF module

Operation

1. Extend the transmitter aerial to full length

2. Switch on the transmitter

3. The RF status LED flashes:

 the channel is free (no guarantee), the RF module

is immediately activated, and the transmitter is

ready to use. “No guarantee” means that the module

may not be able to detect distant transmitters

(approx. > 300 m) because of the influence of en-

vironmental conditions and the local terrain. How-

ever, if the model should fly close to such a transmit-

ter, there is then a risk of interference due to a chan-

nel clash.

4. RF status LED glows constantly  channel in use

The screen also displays the following message for

two seconds:

!Attention! No RF

If Channel-Check finds the channel to be in use

when switched on, you must switch the transmitter

off again before you can use it. Check whether your

channel is already in use by another modeller (in-

cluding transmitters a long way away!). If this is not

the case, the problem may be a transmitter in the

immediate vicinity on an adjacent channel, momen-

tary interference on the channel when you switched

on, etc. Before you switch on again, walk a little way

away from other transmitters, then try again.

22.3. HFM-S Synthesizer RF module

# 4 5693 35 MHz A- and B-band

# 4 5694 40/41 MHz band

# 4 5696 36 MHz

# 4 5695 72 MHz

RF modules exploiting modern Synthesizer technology.

The transmission channel can be selected quickly and

conveniently in the channel set-up menu. No plug-in

crystals are required at the transmitter.

Important: which channels can be used?

Regulations concerning the use of radio-controlled

models vary from country to country. Please make en-

Channel-Check

module

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo7 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info