Bedienungsanleitung Multiplex ROYALevo9 (Seite 19 von 58) (Englisch)

30282

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Instructions

Seite 19

ENGLISH

10.2. The 3-D

digi

-adjustors

The transmitter is fitted with two 3-D digi-adjustors as

standard, and these are used for programming and

setting up the system

10.2.1. Programming using the 3-D digi-

adjustors

At the programming stage, both 3-D digi-adjustors

operate in parallel with the “ENTER” button when

pressed, and in parallel with the „V“ (UP) and „W“

(DOWN) buttons when rotated. You will soon find that

you naturally use one or other by default.

10.2.2. Making adjustments using the 3-D

digi-adjustors

It is possible to assign many different parameters to the

3-D digi-adjustors; you can then use them to adjust the

setting quickly and easily, e.g. when the model is flying.

One typical setting which can be adjusted and opti-

mised in flight is aileron differential:

1. Select the aileron differential parameter (Fig. 1)

2. Press the < F > button

Instead of the parameter value the 3-D digi-adjustor

symbol (Fig. 2) appears. Now press one of the two

3-D digi-adjustors (in our example the right one) to

select it.

If you make a mistake, and the selected parameter

is not to be assigned, simply press the “ENTER” but-

ton.

Now you can quit the menu and go back to the status

display.

In the top line of status displays 1-3 you can now see

that aileron differential “Ail-Diff” is variable using the

right-hand 3-D digi-adjustor (Fig. 3). If you press or ro-

tate the corresponding 3-D digi-adjustor for a moment,

the screen displays the current value of that parameter

(Fig. 4). A closed padlock indicates that the value cannot

be changed at the moment (as a guard against acciden-

tal operation).

If you want to be able to change the value, press the 3-D

digi-adjustor assignment switch <F>. The value can now

be changed. Every change you make is immediately

stored. Pressing the 3-D digi-adjustor assignment

switch once more blocks access to the value again

(symbol: closed padlock).

Fig. 1 Fig. 2

Fig. 3 Fig. 4

Note: If you use flight phases

Setup parameters which have different values for each

flight phase are displayed correctly, i.e. the displayed

values vary according to the currently active flight

phase, and can be adjusted separately in each flight

phase using the appropriate 3-D digi-adjustor.

This is the procedure for erasing the assignment:

1. Hold the appropriate 3-D digi-adjustor pressed in

2. Press the REV/CLR button

 the screen shows „- - -“ and the assignment is

erased

Alternatively you can “overwrite” an assignment at any

time by assigning a new parameter.

Which parameters can be assigned to a digi-

adjustor?

The general rule is that only those parameters with

numeric values can be assigned in this way. However,

there are a few exceptions. In the following Display the

parameter Step (Step width for trim) can not be as-

signed.

Assignable parameters with numeric values are indi-

cated by a high-set hyphen following the parameter

name. If you attempt to assign a parameter which can-

not be assigned, a crossed-out 3-D digi-adjustor symbol

appears when you press the 3-D digi-adjustor assign-

ment button.

If you press a 3-D digi-adjustor in this situation you will

hear an audible error warning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo9 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info