Bedienungsanleitung Multiplex RX-9-DR M-LINK (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

722677

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Operating Instructions for RX-7-DR M-LINK /

RX-9-DR M-LINK 2.4 GHz receivers

MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de Page 2/6

Instructions for RX-7/9-DR M-LINK 2.4 GHz receivers # 985 5319 (10-02-24/MIWA) • Errors and omissions excepted! •

MULTIPLEX

7. RECEIVER CONNECTIONS

This receiver employs the UNI connector system, which is com-

patible with the connector systems used by most radio control

manufacturers (e.g. HiTEC, robbe/Futaba, Graupner/JR).

The receiver sockets are marked as follows:

1, 2, 3 … 7

(… 9)

Servo sockets, channels 1, 2, 3 … 7 (… 9).

Alternatively: receiver battery socket.

In the case of the RX-7-DR M-LINK:

Receiver battery socket

(can also be connected to servo sockets 1 … 7).

Duplicated for extra security: twice the conductor

cross-section, twice the number of contacts.

B/D

Receiver battery socket

(can also be connected to servo sockets 1 … 7

(… 9)).

Duplicated for extra security: twice the conductor

cross-section, twice the number of contacts.

Socket for PC or Diversity cable / MULTImate.

SENSOR Socket for external sensor module.

! When connecting the receiver battery, servos, speed

controllers, sensors ... it is essential to insert the connector

the correct way round. With other makes of component

always check the pin assignment (see symbols on the

receiver)!

8. FIRST USE,FUNCTIONS

8.1 LED Codes

LED code Description

LED Code 0 LED OFF Battery voltage too low

LED Code 1 LED ON No reception

LED Code 2

1,6 sec Binding procedure in progress

1,6 sec

LED Code 3

Normal receiving operation,

no errors

1,6 sec

LED Code 5

Confirmation signal

LED Code 6

1,6 sec 1 – 19 errors

LED Code 7

1,6 sec 20 – 49 errors

LED Code 8

1,6 sec >= 50 errors

8.2 The functions of the SET button

Pressing the SET button on the top of the receiver when

switching on initiates the binding process (Î8.3).

In receive mode, the SET button can be used to trigger two addi-

tional functions. The function selected depends on the length of

the button-press:

1. Save error counter or FAIL-SAFE settings

Press the SET button for 0.5 to 1 second (Î 8.8 and Î 8.5).

2. RESET receiver to factory default settings

Press the SET button for longer than ten seconds (Î8.6).

While the SET button is pressed, the LED indicates the length of

the button-press with time markers:

Press SET

button con-

stantly for

< 2

seconds 2 to 10

seconds > 10

seconds

LED OFF ON OFF

Purpose Save error

counter /

FAIL-SAFE

settings

RESET

to default

settings

! Note:

When the Save process is complete, the LED flashes in confir-

mation (LED code 5 Î 8.1.).

8.3 Binding

The receiver must be set up to match the transmitter before the

system can work. This process is known as “binding”.

! Note:

The signal output to the servo sockets is switched off during the

binding procedure. This means that the servos are “soft”, and do

not move, while the motor connected to a modern electronic

speed controller remains OFF due to the lack of a signal. Never-

theless, it is important to secure the model and keep well clear

of the power system.

The binding process is necessary in the following cases:

x The first time the receiver is used (Î 8.3.1).

x After a receiver RESET (Î 8.6).

x After the transmitter setting for “Fast Response” has been

changed. For more information on this please refer to the

operating instructions supplied with your M-LINK transmitter

or M-LINK RF module.

x After the transmitter setting for the transmitted frequency

range has been changed. For more information on this

please refer to the operating instructions supplied with your

transmitter or M-LINK RF module (“France mode”).

x If the receiver is to be operated in conjunction with a different

M-LINK transmitter.

8.3.1 Sequence of the binding procedure

1. The first step is always to set the transmitter and receiver to

Binding mode:

x Place the transmitter and the receiver aerials close to-

gether.

x Switch the transmitter ON in binding mode.

(see the operating instructions supplied with your M-LINK

transmitter or M-LINK RF module).

x Switch the RX-7/9-DR M-LINK receiver ON in binding

mode:

x Use a pointed object to press and hold the SET button

on the top of the receiver (Î 8.2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex RX-9-DR M-LINK Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info