Bedienungsanleitung MundoClima MUCSR-H3 (Seite 65 von 72) (Englisch)

726079

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

2.3.20.2 Memory Function

Memory switchover: Under the OFF state of the unit, press the Mode and ▲ buttons at the

same time for 5s to switch memory modes. When setting the memory mode, “MEMORY” will be

displayed. If this function is deactivated, the unit will go to the OFF state after power recovery.

Memory recovery: If the memory function is On, the wired controller after power failure will

resume its original running state upon power recovery.

Note: It will take about 5 seconds to save data. Therefore, please do not cut down the power at this

time, or data will fail to be saved.

2.3.20.3 Selection of Centigrade and Fahrenheit

Under the OFF state of the unit, press the Mode and ▼ buttons at the same time for 5s,

Centigrade and Fahrenheit scales will be switched alternately.

2.3.20.4 Ambient Temperature Enquiry

Under On/Off status, press “Confirm” button for 5s, it will enter Enquiry interface. At this time,

what shows on the timer area is the ambient temperature type: 01 or 02 and the temperature will

be shown. “01” means the outdoor ambient temperature and “02” represents the indoor ambient

temperature. Press “Mode” button to switch between those two types. Press any other button

except Mode button or receive the signal from the remote controller will quit from the Enquiry

function. If there is no operation in 20s, the unit will quit from this function automatically.

Note:

①.

If the unit is not connected with the ambient temperature sensor, after 12h electrification,

the display of the ambient temperature sensor will be shielded.

②.

If the outdoor temperature sensor has error, after 12h electrification, the display of the

ambient temperature sensor will be shielded.

2.3.20.5 Indoor fan shutdown mode setting

Under unit OFF status, simultaneously press “Function” and “Timer” button for 5s, the wired

controller will enter parameter setting interface. Press “Mode” button to set till “05” is shown on the

temperature displayed area. Then the unit will enter the indoor fan shutdown mode.

Two options are available for the indoor fan shutdown mode:

Mode 1: When the temperature reaches certain value, the indoor fan will not be shut down

at any mode except heating mode. After the unit is shut down, for the duct type unit and the floor

ceiling type unit, the indoor fan will blow the extra heat for 60s and then stop running. For the

cassette type unit, its indoor fan will operate at low fan speed and blow the extra heat for 60s only

when error happens to it.

Mode 2: No matter the unit is under which mode, the indoor fan will keep running for 10s after

the temperature reaches certain value, then it will stop.

Press “▲” or “▼” button to adjust the mode. Under Mode 1/2, “00”/ “01” will show up in the

timer area. Then press “Enter/Cancel” button to save the settings. The setting procedures are

shown as Fig.25:

Cassette Serie H3 - Super DC Inverter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MundoClima MUCSR-H3 Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info