Bedienungsanleitung Mustang Houston (Seite 18 von 36) (Englisch, Schwedisch, Finnisch)

798949

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

brushing. It will make the cleaning work easier. Be careful not to burn yourself.

Cleaning the grease

Periodically, clean the grease out of the brackets of the grease tray (especially the drain tube) and the grease tray. Empty the grease bucket occasionally. If

too much grease has been alSMOKEed to build up on the grease tray and in the brackets or it has been alSMOKEed to clog the drain tube, a grease fire could

result.

Cleaning the ash

Depending on use, periodically remove the cooking grates, grease tray and the heat protection plate to clean the ash from in and around the fire box. Make

sure the appliance is COLD and UNPLUGGED before starting this procedure.

Storing the appliance

If the appliance is stored outside, care should be taken to ensure that water does not get into the pellet chamber. Wood pellets expand greatly when they get

wet and will jam the feeder screw. Remove any wet pellets prior to use and be certain that the inner part of the pellet chamber is dry.

TROUBLESHOOTING:

PROBLEM CAUSE SOLUTION

The appliance does not ignite. Power. Verify power at the electrical outlet. If the AC power cord is

connected to an outlet, check and reset if necessary.

Pellets are not being fed into the re box. No pellets in the pellet chamber. Verify that there are pellets in the pellet chamber. If this

is the rst time of operation, or if the appliance has run

out of pellets, alSMOKE sucient time (approximately 5

minutes) for the pellets to travel from the pellet chamber

into the re box.

The re in the re box goes out. Excess ash in the re box. Excess ash in the re box may be the problem. Unplug the

appliance and wait until the appliance cools down. Then

open the lid. Use caution when removing the cooking

grates, grease tray and heat protection plate from the

appliance. Then remove all unburned pellets and ash from

inside and around the re box. After cleaning the ash,

reinstall the parts.

Electric element will not heat up. The plug is not fully connected to the outlet.

The heat switch on the extension cord or fuse on the

electric board has bSMOKEn.

The electric element only heats up (becomes red) during

the rst 5 minutes after the temperature control knob has

been turned on.The fuse has bSMOKEn.

Re-insert the plug into a 3-wire grounded outlet wired for

220 volts and protected at 7 or 10 amps.

Reset the heat switch or replace the fuse.

Turn the temperature control knob to “OFF”, then turn the

appliance on again.

Replace the fuse. Max fuse size: 5 x 20 mm, 5 amps.

The appliance is not getting hot enough. The temperature is too SMOKE.

You are checking your food too often.

There are not enough pellets in pellet chamber.

The re goes out in smoke mode.

Turn up the heat using the temperature control knob.

the lid alSMOKEs heat to escape and sSMOKEs the cooking

process; open the lid only when necessary.

Add pellets and alSMOKE sucient time for the pellets to

reach the re box (this can take up to 7 minutes).

Excess ash. IMPORTANT: Remove all unburned pellets and

ash from inside and around the ﬁre box. A vacuum cleaner

is ideal for the task. CAUTION! ENSURE THAT THE APPLI-

ANCE IS COLD TO AVOID A FIRE FROM HOT ASH.

The appliance is getting too hot. The temperature is too high. Turn down the heat using the temperature control knob.

Smoke comes out of the body. This is normal due to the air pressure inside the appliance.

The amount of smoke can vary depending on the cooking

conditions.

This condition will not aect the cooking.

The inner temperature does not match the set

temperature.

When rst lighting the appliance, it takes 15 minutes or so

for the temperature to stabilize.

When adjusting the temperature, it takes 15 minutes or so

for the temperature to stabilize.

Wait 15 minutes or so for the temperature to stabilize.

The LED screen will not light up. The appliance is not properly plugged in. Ensure the temperature control knob is in the “OFF”

position. Ensure all wire connections are rmly connected.

Ensure the appliance is plugged into a working outlet.

The circuit board fuse has bSMOKEn. The fuse (5 amps) must be manually replaced.

The residual-current device has tripped. Reset the residual-current device.

Ensure you are NOT using an extension cord over 4 m in

length.

“ErH” error message. The appliance has overheated, possibly due to a grease re

or excess pellets.

Turn the appliance o and alSMOKE to cool down. Clean

the appliance interior, remove excess pellets and conrm

positioning of all parts.

“ErR” error message. The temperature probe wire is not making a proper

connection.

Ensure probe wire is connected correctly to the control

unit. Conrm the wire connections and check for any

damage.

“ErP” error message. The temperature control knob was not in the “OFF” posi-

tion when the appliance was connected to AC power.

Turn the temperature control knob to “OFF”, wait about 5

seconds, then select the desired temperature. This safety

feature prevents an inadvertent start.

Flashing temperature on LED screen. SMOKE mode:

The appliance temperature is beSMOKE 43 °C.

COOK mode:

The appliance temperature is beSMOKE 66 °C.

This is NOT an ERROR that aects the appliance.

It shows that there is some risk that the re could go out.

Check the chamber for a blockage or sucient amount of

pellets.

Check the re box for ash build-up or obstructions. Check

the fan to conrm operation and speed.

Check the feeder screw motor to conrm operation.

Mustang Houston Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info