Bedienungsanleitung Mustek PowerMust 400 (Seite 3 von 48) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Polnisch, Finnisch)

677934

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

4 hours

CAUTION: NEVER connect a laser printer or scanner to the UPS unit. This may

cause the damage of the unit.

Attention hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous

voltage still may be accessible through supply from battery. The battery supply should be therefore

disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service

work inside the UPS is necessary.

CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries

and the required precautions. Keep unauthorized personnel away from batteries.

CAUTION! When replacing the batteries, use the same number and type of batteries.

CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.

CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or mutilate the battery

or batteries. Released electrolyte is harmful to the skin and eyes.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

CAUTION! A battery can present a risk of electric shock and high short circuit current. The following precaution

should be observed before replacing batteries:

1) Remove watches, rings, or other metal objects.

2) Use tools with insulated handles.

3) Wear rubber gloves and boots.

4) Do not lay tools or metal parts on top of batteries.

5) Disconnect charging source prior to connecting or disconnecting batteries terminal.

Before installation, please make sure nothing inside of package is damaged. To protect your equipment

from power failure, be sure that power switch must be kept in the “ON” position. Following below steps to

install your UPS unit.

❶

Placement & Storage Conditions

Install the UPS in a protected area that is free of excessive dust and has adequate air flow. Please place the

UPS away from other units at least 20 cm to avoid interference. Do NOT operate the UPS where the

temperature and humidity is outside the specific limits. (Please check the specs for the limitations.)

❷

Connect to Utility and Charging

Plug in the AC input cord to the wall outlet. For the best results, suggest to charge the battery at least 4 hours

before initial use. The unit charges its battery while connecting to the utility.

❸

Connect the Loads

Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the power switch of UPS

unit, then devices connected to the UPS will be protected by UPS unit.

❹Connect Modem/Phone/Network for Surge Protection (Only for the model with RJ-11/RJ45)

Connect a single modem/phone line into surge-protected “IN” outlet on the back panel of the UPS unit. Connect

from “OUT” outlet to the computer with another phone line cable.

❺Connect Com. Port and Install Software (only for the model with RS-232/USB port)

To enable remote UPS shutdown/start-up and status monitoring, connect the communication cable from the

USB/RS-232 port and the other to the communication port of your PC. With the monitoring software installed,

you can schedule UPS shutdown/start-up and monitor the UPS status.

❻

Turn On/Off the Unit

Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing again the power switch.

MODEL

400

600

800

CAPACITY

400VA/240W

600VA/360W

800VA/480W

Input Voltage

220/230/240VAC

Input Voltage Range

162-290 VAC

Output Voltage Regulation

± 10 % (Bat. mode)

Frequency Range (Batt. Mode)

50Hz +/-1 Hz

Transfer Time

Typical 2-6 ms

Waveform

Simulated Sine Wave

Battery Type & No

12V/4.5Ahx1

12V/7Ahx1

12V/9Ahx1

Charging Time

4-6 hours recover to 90% capacity

Dimension (DxWxH) mm

LED: 279 x 101 x 142 / LCD: 300 x 101 x 142

Net Weight (kgs)

LED

3.55

4.2

4.9

LCD

3.7

4.4

5.0

Humidity

0-90% RH @ 0-40°C non-condensing)

Noise Level

Less than 40dB

MODEL

1000

1500

2000

CAPACITY

1KVA/600W

1.5KVA/900W

2KVA/1200W

Input Voltage

220/230/240VAC

Input Voltage Range

162-290 VAC

Output Voltage Regulation

± 10 % (Bat. mode)

Frequency Range (Batt. Mode)

50Hz +/-1 Hz

Transfer Time

Typical 2-6 ms

Waveform

Simulated Sine Wave

Battery Type & No

12V/7Ah x 2

12V/9Ah x 2

Charging Time

4-6 hours recover to 90% capacity

Dimension (DxWxH)

320 x 130 x 182

Net Weight (kgs)

8.2

10.4

Humidity

0-90% RH @ 0-40°C (non-condensing)

Noise Level

Less than 40dB

Problem

Possible Cause

Solutions

No LED display on the front

panel.

Low battery.

Charge the UPS at least 6 hours.

Battery fault.

Replace the battery with the same type of

battery.

The UPS is not turned on.

Press the power switch again to turn on

the UPS.

Alarm continuously

sounds when the

mains is normal.

The UPS is overload.

Remove some loads first. Before

reconnecting equipment, please verify

that the load matches the UPS capability

specified in the specs.

When power fails, back-up time

is shorten.

The UPS is overload.

Remove some critical load.

Battery voltage is too low.

Charge the UPS at least 6 hours.

Battery defect. It might

be due to high

temperature operation

environment, or improper

operation to battery.

Replace the battery with the same type of

battery.

The mains is normal but the

unit is on battery mode.

Power cord is loose.

Reconnect the power cord properly.

User Manual

Mustek PowerMust 400 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info