Bedienungsanleitung NAD C 326 BEE (Seite 9 von 16) (Englisch)

493507

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

10 MAIN IN: Connections to an external pre-amplier or processor, such as

a surround-sound decoder. In normal use, this should be connected to

PRE OUT sockets with the links supplied. To connect your NAD C 326BEE

to external processor or pre-amplier, remove rst these links. Use a

twin RCA-to-RCA lead to connect the left and right “Audio Output” of

the pre-amp or processor to the Main In sockets.

Always turn the C 326BEE and associated external power ampliers OFF

before connecting or disconnecting anything to the MAIN IN sockets.

11 SOFT CLIPPING™: Enables NAD’s proprietary Soft Clipping circuitry

on all channels. At [ON] position, Soft Clipping gently limits the output

of the C 326BEE to minimize audible distortion should the amplier be

over-driven. Soft Clipping may simply be left ON at all times to reduce

the likelihood of audible distortion from excessive volume settings.

However, for critical listening and to preserve optimum dynamics, you

may wish to defeat it by setting this switch to “OFF” position.

The SOFT CLIPPING indicator on the front panel will illuminate when the

C 326BEE is in Soft Clipping mode. Refer also to the item below about

“POWERDRIVE”.

POWERDRIVE

The C 326BEE uses NAD’s proprietary PowerDrive™ amplier technology

for all channels to preserve accurate, linear reproduction regardless

of the loudspeaker. This uniquely ecient power-supply topology

provides the real-world benets of high dynamic power that remains

uncompromised by low-impedance speakers.

By adding a second high-voltage rail to our well regulated high-

current power supply, we get an “overdrive” that can nearly double the

continuous power on a short term dynamic power basis. PowerDrive

oers greater amplier stability and low impedance drive capability,

resulting in less distortion when driving real speakers with real program

material.

12 +12V TRIGGER OUT: The +12V TRIGGER OUT is used for controlling

external equipment that is equipped with a +12V trigger input. This

output will be 12V when the C 326BEE is ON and 0V when the unit is

either OFF or in standby. This output can drive a load up to 50mA at

12V.

13 IR IN/OUT: These mini-jacks accept and output remote-controlled

codes in electrical format, using industry-standard protocols, for use

with “IR-repeater” and multi-room systems and related technologies.

IR IN: This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the C 326BEE from a remote location.

IR OUT: When connected to the IR IN of an ancillary equipment, direct

the ancillary equipment’s own remote control to the C 326BEE’s infrared

receiver to command or control the linked unit.

All NAD products with IR IN/IR OUT features are fully compatible with

the C 326BEE. For non-NAD models, please check with your other

product’s service specialists as to their compatibility with the C 326BEE’s

IR features.

14 SPEAKERS: Connect the right speaker to the terminals marked “R +”

and “R-” ensuring that the “R+” is connected to the “+” terminal on your

loudspeaker and the “R-” is connected to the loudspeaker’s “-” terminal.

Connect the terminals marked “L+” and “L-” to the left speaker in the

same way.

Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded wire to

connect loudspeakers to your C 326BEE. The high-current binding post

terminals can be used as a screw terminal for cables terminating in

spade or pin sockets or for cables with bare wire ends.

The C 326BEE is designed to produce optimum sound quality when

connected to speakers with impedances within its operating range.

Please make sure that all the speakers are rated 4 ohms minimum per

speaker.

15 POWER SWITCH: The POWER switch supplies the master AC mains

power for the C 326BEE. When this switch is at ON position, the

C 326BEE is in standby mode as shown by the amber status condition

of the standby LED. Toggle the front panel’s STANDBY button to switch

ON the C 326BEE or back to standby mode. If you intend not to use the

C 326BEE for long periods of time (such as when on vacation), switch

the POWER switch to the OFF position. When the POWER switch is at

OFF position, the front panel power button or SR 8 remote control

cannot activate the C 326BEE.

16 AC MAINS INPUT: The C 326BEE comes supplied with a separate AC Mains

cable. Before connecting the cable to a live wall socket, ensure that it is

rmly connected to the C 326BEE’s AC Mains input socket rst. Connect

only to the prescribed AC Outlet, i.e., 120V 60 Hz (North America version

only) or 230V 50 Hz (European version only).. Always disconnect the AC

Mains cable plug from the live wall socket rst, before disconnecting the

cable from the C 326BEE’s Mains input socket.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 326 BEE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 326 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info