Bedienungsanleitung NAD C 356 BEE (Seite 9 von 18) (Englisch)

493506

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

9 TAPE 2 IN/OUT: Connections for analog recording and playback to

a tape recorder of any type. Using twin RCA-to-RCA leads, connect

the left and right “Audio Output” of the tape recorder to the TAPE 2 IN

sockets for playback. Connect the left and right “Audio Input” of the tape

recorder to the TAPE 2 OUT sockets for recording.

10 TAPE MONITOR IN/OUT: Connections for analog recording and

playback to a secondary tape recorder of any type. Using twin

RCA-to-RCA leads, connect the left and right “Audio Output” of the

tape recorder to the TAPE MONITOR IN sockets for playback and

tape monitoring. Connect the left and right “Audio Input” of the tape

recorder to the TAPE MONITOR OUT sockets for recording.

TO MAKE A RECORDING

When any source is selected, its signal is also fed directly to any tape

recorder connected to the TAPE 2 OUT or TAPE MONITOR OUT for

recording.

TAPE TO TAPE COPYING

You can copy between two tape recorders connected to your C 356BEE.

Put the source tape in the recorder connected to TAPE 2 and the blank

tape into the recorder connected to TAPE MONITOR. By selecting TAPE2

input you can now record from TAPE 2 to TAPE MONITOR and monitor

the signal coming from the original tape.

NOTE

There will be no TAPE 2 output when TAPE 2 is the selected source input.

This prevents feedback through the recording component thereby

preventing possible damage to your speakers. The same applies to TAPE

MONITOR IN/OUT.

11 PRE OUT 1: The PRE OUT 1 sockets can be used to drive an additional

power amplier. Use a twin RCA-to-RCA lead to connect the left and

right “Audio Input” of the Power amplier or processor to the PRE OUT 1

sockets.

Always turn the C 356BEE and associated external power ampliers OFF

before connecting or disconnecting anything to the PRE OUT 1 sockets.

The PRE OUT 1 output signal will be aected by the C 356BEE’s volume

and tone control settings.

12 PRE OUT 2: Connections to an external power amplier or processor,

such as a surround-sound decoder. In normal use, this should be

connected to the MAIN IN sockets with the links supplied. To connect

your C 356BEE to an external processor or amplier, remove rst these

links. Use a twin RCA-to-RCA lead to connect the left and right “Audio

Input” of a power amplier or processor to the PRE OUT 2 sockets.

Always turn the C 356BEE and associated external power ampliers OFF

before connecting or disconnecting anything to the PRE OUT 2 sockets.

The PRE OUT 2 output signal will be aected by the C 356BEE’s volume

and tone control settings.

13 MAIN IN: Connections to an external preamplier or processor, such as

a surround sound decoder. In normal use, this should be connected to

PRE OUT 2 sockets with the links supplied. To connect your C 356BEE to

an external processor or preamplier, remove rst these links. Use a twin

RCA-to-RCA lead to connect the left and right “Audio Output” of the

preamplier or processor to the MAIN IN sockets.

Always turn the C 356BEE and associated external preampliers OFF

before connecting or disconnecting anything to the MAIN IN sockets.

14 SOFT CLIPPING™: Enables NAD’s proprietary Soft Clipping circuitry

on all channels. At [ON] position, Soft Clipping gently limits the output

of the C 356BEE to minimize audible distortion should the amplier be

over driven. Soft Clipping may simply be left ON at all times to reduce

the likelihood of audible distortion from excessive volume settings.

However, for critical listening and to preserve optimum dynamics, you

may wish to defeat it by setting this switch to “OFF” position.

The SOFT CLIPPING indicator on the front panel will illuminate when the

C 356BEE is in Soft Clipping mode. Refer also to the item below about

“POWERDRIVE”.

POWERDRIVE

The C 356BEE uses NAD’s proprietary PowerDrive™ amplier technology

that provides high dynamic power and low impedance drive capability.

By adding a second high-voltage rail to our well regulated high-

current power supply, we get an “overdrive” that can nearly double the

continuous power on a short term dynamic power basis. This uniquely

ecient power supply topology provides the real world benets of

high dynamic power that remains uncompromised by low impedance

speakers.

15 SPEAKERS A, B: The C 356BEE is equipped with two sets of speaker

connectors. Use the SPEAKERS A terminals for the “main” speakers and

use the SPEAKERS B terminals for a second pair, for example, extension

speakers located in another room.

Connect the right speaker to the terminals marked “R +” and “R-”

ensuring that the “R+” is connected to the “+” terminal on your

loudspeaker and the “R-” is connected to the loudspeaker’s “-” terminal.

Connect the terminals marked “L+” and “L-” to the left speaker in the

same way.

Always use heavy duty (16 gauge; 1.5mm

or thicker) stranded wire to

connect loudspeakers to your C 356BEE. The high-current binding post

terminals can be used as a screw terminal for cables terminating in

spade or pin sockets or for cables with bare wire ends.

16 SWITCHED AC OUTLET (120V version only): This convenience outlet

can supply switched power to another component or accessory. With

the POWER switch at the rear panel set to ON position, this outlet is

powered ON or OFF by the front panel STANDBY switch or by the SR 8’s

[ON/OFF] buttons. The total draw of all devices connected to this outlet

must not exceed 120 watts.

17 AC MAINS INPUT: The C 356BEE comes supplied with a separate

detachable mains power cord. Before connecting the plug to the mains

power source, ensure that it is rmly connected to the C 356BEE’s AC

Mains input socket rst. Connect only to the prescribed AC outlet,

i.e., 120V 60 Hz (for 120V version models of C 356BEE only) or 230V

50 Hz (for 230V version models of C 356BEE only). Always disconnect

the mains power plug from the mains power source rst, before

disconnecting the cable from the C 356BEE’s AC Mains input socket.

18 POWER SWITCH: The POWER switch supplies the master mains power

for the C 356BEE. When this switch is at ON position, the C 356BEE

is in standby mode as shown by the amber status condition of the

standby LED. Toggle the front panel’s STANDBY button to switch ON the

C 356BEE or back to standby mode. Switch o the POWER switch if you

intend not to use the C 356BEE for long periods of time (such as when

on vacation). It is not possible to switch ON the C 356BEE using the

front panel STANDBY button or SR 8 remote control’s [ON] button if the

rear panel POWER switch is switched o.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

NAD C 356 BEE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 356 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info