Bedienungsanleitung NAD C 390 DD (Seite 8 von 26) (Englisch)

493504

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

6 GROUND TERMINAL

The C 390DD requires a grounded AC receptacle or a separate earth

ground. Use this terminal to properly ground your C 390DD. The

C 390DD can be connected to ground by connecting a ground lead

wire or similar to this ground terminal. After insertion, tighten the

terminal to secure the lead.

EXAMPLE ILLUSTRATION OF GROUNDING THE C 390DD VIA THE

REAR PANEL GROUND TERMINAL

NOTES

• The above illustration shows the C 390DD being connected to ground

via a metal water pipe. There maybe other grounding conductor points

in your home. Consult with a licensed electrician to properly locate

or correctly install a grounding conductor in your home. NAD is not

responsible for any malfunction, damage or costs associated with the

installation, connection or grounding of your C 390DD.

• The grounding wire is not supplied with your C 390DD.

7 +12V TRIGGER OUT

The +12V TRIGGER OUT is used for controlling external equipment that

is equipped with a +12V trigger input.

• Connect this +12V TRIGGER OUT to the other equipment’s

corresponding +12V DC input jack using a mono cable with 3.5mm

male plug.

• This output will be 12V when the C 390DD is ON and 0V when the

unit is either OFF or in standby mode.

+12V TRIGGER IN

With this input triggered by a 12V DC supply, the C 390DD can be

switched ON remotely from standby mode by compatible devices such

as ampliers, preampliers, receivers, etc. If the 12V DC supply is cut o,

the C 390DD will return to standby mode.

• Connect this +12V Trigger input to the remote device’s

corresponding +12V DC output jack using a mono cable with

3.5mm male plug. The controlling device must be equipped with a

+12V trigger output to use this feature.

8 IR IN

This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the C 390DD from a remote location.

9 RS 232

NAD is a certied partner of AMX and Crestron and fully supports

these external devices. Check out the NAD website for information

about AMX and Crestron compatibility with NAD. See your NAD audio

specialist for more information.

• Connect this interface using RS-232 serial cable (not supplied)

to any Windows compatible PC to allow remote control of the

C 390DD via compatible external controllers.

• Refer to the NAD website for information about RS232 Protocol

documents and PC interface program.

10 PRE OUT/SUBW (1,2)

• These output terminals have dual function. They are used either as

PRE OUT or SUBWOOFER terminals.

• These terminals are enabled or disabled via the Pre Out/Subwoofer

sub-menu of the SETUP menu.

• Refer also to the item about PRE OUT/SUBWOOFER at the USING

THE C 390DD section of the OPERATION page.

11 AC MAINS INPUT

The C 390DD comes supplied with a separate detachable mains power

cord. Before connecting the plug to the mains power source, ensure

that it is rmly connected to the C 390DD’s AC Mains input socket rst.

• Always disconnect the mains power plug from the mains power

source rst, before disconnecting the cable from the C 390DD’s AC

Mains input socket.

12 POWER

• Supply the AC mains power to the C 390DD.

• When the POWER switch is set to ON position, the C 390DD goes

to standby mode as shown by the amber status condition of the

Standby LED. Press the front panel Standby button or AVR 4 remote

control’s [ON] button to switch ON the C 390DD from standby

mode.

• If you intend not to use the C 390DD for long periods of time (such

as when on vacation), switch o the POWER switch.

• With POWER switched o, neither the front panel Standby button

nor AVR 4 remote control’s [ON] button can activate the C 390DD.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 390 DD Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 390 DD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info