Bedienungsanleitung NAD C 390 DD (Seite 11 von 26) (Englisch)

493504

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

USING THE AVR 4 REMOTE CONTROL

The AVR 4 remote control handset handles the key functions of the C 390DD. The AVR 4 can also be

used to directly command other NAD products that respond to applicable common remote control

codes. This includes other NAD Stereo Receiver, Integrated Amplier and Preamplier models. It has

additional controls to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DB

Tuners. It will operate up to a distance of 23ft (7m). Alkaline batteries are recommended for maximum

operating life. Two AA batteries should be tted in the battery compartment at the rear of the Remote

Control handset. When replacing batteries, check that they have been put in the right way round, as

indicated on the base of the battery compartment.

NOTE

The remote control handset supplied with the C 390DD is of a universal NAD type, designed to

operate several NAD models. Some buttons are applicable only to specic NAD models. Contact

your dealer or NAD audio specialist for assistance.

1 ON, OFF

The AVR 4 remote has a separate ON and OFF button.

ON: Switch C 390DD from Standby mode to operating mode.

OFF: Switch C 390DD to Standby mode.

NOTE

In order to turn ON the C 390DD from standby mode or back to standby mode, the rear panel

POWER switch must be in the ON position.

2 DEVICE SELECTOR

A Device Selector button determines only what component the AVR 4 will command; it does not

perform any function on the C 390DD.

• Press desired Device Selector button for the applicable buttons to be directed to a “page” of

commands relevant to the selected device. Upon selecting a Device, you can now press the

corresponding AVR 4 control buttons applicable for the selected Device.

3 INPUT SELECTORS

Refer to the corresponding labels printed in the remote control faceplate and their respective

assigned buttons to make use of these functions.

• Set the DEVICE SELECTOR to “AMP” in order to gain access to these buttons.

The following table illustrates the corresponding C390DD source input when one presses the

specied AVR 4 button.

AVR 4 BUTTON C390DD SOURCE INPUT

INPUT 1 Digital Coaxial 1

INPUT 2 Digital Coaxial 2

INPUT 3 Digital Optical 1

INPUT 4 Digital Optical 2

INPUT 5 Digital AES EBU

INPUT 6 Computer

INPUT 7 Digital USB Back

FRONT Digital USB Front

SOURCE 5/6

Toggle through the input sources including those from DD HDM‑1 and DD AP‑1 modules

when installed.

4 DIMMER

Reduce or restore front panel display brightness.

5 MUTE

• Temporarily mute audio output or restore audio from mute mode.

• MUTE mode is indicated by “MUTE” shown in the front panel display.

• Adjusting the volume level via the AVR 4 or the front panel volume knob will automatically

release the mute function.

• Alternately press and hold [MUTE] button to enable or disable speakers (“Speakers ON” or

“Speakers OFF” is shown at the front panel display).

IDENTIFICATION OF CONTROLS

AVR 4 REMOTE CONTROL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 390 DD Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 390 DD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info