Bedienungsanleitung NAD C 390 DD (Seite 22 von 26) (Englisch)

493504

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

SPEAKERS ON/OFF ‑ HEADPHONE

There are times when you may want the speakers to be silent but with

Preamp Output remaining active. An example would be driving an external

Headphone Amplier or Powered Speaker.

The HEADPHONE feature is premised upon having the SPEAKERS turned

ON or OFF. The speakers can be turned ON or OFF via the following

method.

• Alternately press and hold AVR 4’s MUTE button to enable or disable the

speakers (“Speakers ON” or “Speakers OFF” is shown at the front panel

display).

SPEAKERS ON

• SPEAKERS terminal is enabled or turned ON.

SPEAKERS OFF

• SPEAKERS terminal is disabled or turned OFF.

• “Headphone ON” is shown on the lower portion of the current Source.

• With SPEAKERS turned OFF, one can hear the current source as

streamed through PRE-OUT/SUBW or COAXIAL OUT/OPTICAL OUT

terminals via the amplier, receiver or other applicable media they are

connected to.

IMPORTANT NOTES

• Only digital sources are available at COAXIAL OUT/OPTICAL OUT.

All other sources including the digital sources can be heard through

SPEAKERS terminal and also streamed via PRE-OUT/SUBW terminals.

• Subwoofer cannot be enabled if the speakers are set to “Speakers OFF”.

USB MODE

The C 390DD is equipped with three USB input terminals – USB Front, USB

Back and Computer. Using either “USB Front” or “USB Back”, the C 390DD

can play back MP3/WMA/FLAC les stored in external USB (Universal Serial

Bus) mass storage devices. Use “Computer” to interface computer audio

and directly stream 24/96 PCM content from your PC or MAC.

DIGITAL USB FRONT/DIGITAL USB BACK USB TYPE A

• Supports playback of MP3, WMA and FLAC les

MP3/WMA: 48 kHz

FLAC: 24 bit/48 kHz

• FAT12/16 root directory up to 256 les (short names)

• FAT12/16/32 up to 65535 les (short names) per directory

• FAT le system limited to 2TB

• File and directory names limited to 64 characters

• Up to 16 maximum level of directories

• Supports USB version 1.1

COMPUTER USB TYPE B

• Supports 24 bit/96 kHz PCM content from PC or MAC

NOTE

Typical USB mass storage devices compatible with C 390DD include

portable ash memory devices and external hard drives (FAT32

formatted).

IMPORTANT NOTE ABOUT CONTROL BUTTONS

The control buttons mentioned in this manual may refer to either front

panel or remote control buttons. Check out the buttons shown with

respect to the actual front panel or remote control. There are front panel

and remote control buttons that may not exactly look alike but have

the same function – example: front panel’s [d/f/a/s] and remote

control’s [D/F/A/S]; front panel’s [a SOURCE s] and remote control’s

[SOURCE5/6].

LISTENING TO USB DEVICE

1 Toggle [a SOURCE s] button to select “USB Front” or “USB Back” source

mode. If no USB mass storage device is connected to USB Front or

USB Back input, “Please Insert Device” will be displayed in the VFD. If

there are no applicable MP3/WMA/FLAC les available in the USB mass

storage device, the VFD will show “No les found”.

2 Plug-in the USB mass storage device to the USB input – MP3, WMA or

FLAC les or folders will be displayed in the VFD.

3 Use [d/f/a/s] to select through the les or folder. Press [s], [S] or

[ENTER] to start playback of particular le.

4 Toggle AVR 4’s [DISP] button to show information about the current le.

USB PLAYBACK CONTROLS

Using the AVR 4 remote control, the following playback control buttons are

applicable for USB playback. Set DEVICE SELECTOR to MP for USB playback

control.

ENTER/S : Select USB le and at the same time start playback.

A : Return to previous display.

4 : Resume playback from pause mode.

j : Pause current playback.

9 : Skip back to the preceding song.

0 : Skip forward to the next song.

RPT: Repeat track (le), folder, all or repeat o.

DISP: Toggle to display applicable information about the le currently

playing.

IMPORTANT NOTICE

Do not disconnect the USB mass storage device during playback as it

may damage the C 390DD.

LISTENING TO A COMPUTER

Use Type A to Type B cable connector to directly stream 24/96 PCM

content from your PC or MAC to the C 390DD. Ensure that the Sound or

Audio device setting of your computer is set to “NAD USB Audio”.

MINIMUM PC SYSTEM REQUIREMENT

Microsoft Windows XP Service Pack 2 or higher, Microsoft Windows 7

FOR MAC USERS

Minimum Mac OS X Snow Leopard (version 10.6) and later versions.

RENAMING A SOURCE INPUT

A particular source input can be renamed according to your preference.

You can use up to 20 characters in renaming a source input. Below is the

procedure on how to rename a source input.

Example: Rename “Digital Coaxial 1” to “BD Player”.

1 Toggle [a SOURCE s] button until “Digital Coaxial 1”.

2 Then, press and hold front panel’s [a SOURCE] button until “Digital

Coaxial 1” is shown in the lower section of the VFD and with “D” ashing.

Note that “Digital Coaxial 1” is also shown at upper section of the VFD.

3 Within 5 seconds, toggle the [d/f] buttons to select the rst character

(“B” from the alphabetical list). The ranges of characters available are

A-Z, a-z, _ (space) and 0-9.

4 Press [s] to select the character and at the same time move on to the

next character. Repeat steps 3 and 4 for each character in sequence.

5 Complete the renaming process by pressing the [ENTER] button again

to save the new source input name.

NOTE

The renaming process will be automatically terminated if no button

is pressed within 5 seconds. Any renamed characters at the time of

termination will not be saved.

OPERATION

OTHER FEATURES

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NAD C 390 DD Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 390 DD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info