Bedienungsanleitung NAD C 426 (Seite 8 von 15) (Englisch)

493513

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

1 FM ANTENNA TERMINAL: Connect the supplied wire “dipole” FM

antenna to the FM antenna terminal using the supplied “balun” adapter.

It will usually work best when mounted on a vertical surface such as a

wall, with arms fully outstretched forming a horizontal “T” perpendicular

to the origin point of the signal.

2 AM ANTENNA TERMINAL: Connect the supplied AM loop antenna to

these terminals. If an external AM antenna is used, make connections

to the AM and GND terminals in accordance with the instructions

supplied with the antenna. Refer also to the item about ASSEMBLING

THE LOOP ANTENNA at the LISTENING TO AM/FM RADIO section of the

OPERATION page.

3 OUTPUT (L, R): Connect to the corresponding analog audio input of

an amplier, receiver or stereo system.

4 RS-232: Connect this interface using RS-232 serial cable (not supplied)

to any Windows® compatible PC to allow remote control of the C 426

via compatible external controllers. NAD is a certied partner of AMX

and Crestron and fully supports these external devices. Check out the

NAD website for information about AMX and Crestron compatibility

with NAD. See your NAD audio specialist for more information.

5 IR IN: This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the C 426 from a remote location. Most NAD products with IR

OUT are fully compatible with the C 426.

6 +12V TRIGGER IN: This input allows the C 426 to be switched remotely

to standby mode and ON by ancillary equipment, such as an amplier,

preamp, AV processor, etc. The controlling device must be equipped

with a 12V trigger output to use this feature. Connect this +12V trigger

input to the remote component’s corresponding +12V DC output jack

using a mono cable with 3.5mm male plug.

7 AC MAINS INPUT: The C 426 comes supplied with a separate AC Mains

cable. Before connecting the cable to a live wall socket, ensure that it

is rmly connected to the C 426’s AC Mains input socket rst. Connect

only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V version

models of C 426 only) or 230V 50 Hz (for 230V version models of C 426

only). Always disconnect the AC Mains cable plug from the live wall

socket rst, before disconnecting the cable from the C 426’s Mains input

socket.

If you intend not to use the C 426 for long periods of time, disconnect

the AC mains cable plug from the live AC wall socket.

WARNING

If the male plug of the mono cable (with or without +12V DC) is

connected to C 426’s +12V TRIGGER IN, the Standby button in the front

panel as well as the corresponding ON/OFF function keys in the remote

control will be disabled. Unplug the mono cable to maintain normal

power ON/OFF function procedures.

IDENTIFICATION OF CONTROLS

REAR PANEL

1 432 5 6 7

ATTENTION!

Please make sure that the C 426 is powered o or unplugged before making any connections. It is also advisable to power down or unplug all associated

components while making or breaking any signal or AC power connections.

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 426 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 426

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info