Bedienungsanleitung NAD C 556 (Seite 4 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

602901

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

USING THE C 556

This turntable has been engineered to give extremely good musical

reproduction. Inherent in the design are several features that improve

sound quality and focus the manufacturing costs where they are most

needed.

Example: Speed change is achieved by manually moving the drive belt

from one pulley to another as shown below.

The cost saving from the use of manual speed change allows a very

expensive low vibration motor with an accuracy exceeding that of

conventional designs to be employed.

NOTES ON INSTALLATION

1 Try to mount the turntable on a rigid, level surface. A light shelf screwed

to the wall or in an alcove would be ideal. Avoid mounting on hollow or

heavy cabinets, or anything mounted on a wooden oor.

2 DO NOT lift the centre hub from its bearing. The bearing is factory

assembled with a lm of thick lubricant. Disturbance of this can cause

serious problems with speed variation and wear.

3 The tonearm is automatically earthed (or ground) through the arm

cable screening. No other earthing should be necessary.

4 Save the packing, in case the turntable has to be transported in the

future.

TIPS AND SUGGESTIONS

1 Try to keep the lid closed while playing records. This will prevent dust

falling onto the records and make cleaning unnecessary. There may also

be a sound improvement.

2 Try to leave the turntable running during a record playing session.

Switch ON before the start, and only switch OFF after the last record has

nished. Changing records while the platter revolves is easier than it

sounds!

3 When the record reaches the end of one side, remember to lift the

stylus o the surface of the record using the lift/lower mechanism.

4 When switching on the turntable, especially at 45rpm, it is

recommended to give the platter a quick spin clockwise as the “ON”

switch is pressed. This relieves strain on the motor and belt.

5 No maintenance should be necessary. If the turntable is working well,

leave it alone. Some settling of the anti-vibration feet may cause the

turntable to lean backwards slightly after a few months, but this is

nothing to worry about.

6 Don’t use a record cleaner that works as the record plays, or any

cleaners that use water or uids. Don’t touch the playing surface of

records. Visible dust on the record surface is simply brushed aside by

the stylus, and any that collects there can easily be blown away.

7 Don’t use any polishes on the turntable or lid. To clean or dust, wipe

gently with a soft cotton duster (slightly damp, only if necessary).

ENJOY THE MUSIC!

QUICKSTART FOR FACTORY FITTED CARTRIDGE

The C 556 is designed to be setup and used seamlessly. Setup the factory

tted cartridge by the following setup instruction.

1 Push the counterweight as close as

possible to the stop point in order to

attain the correct tracking weight. This

will automatically set the tonearm to

within the recommended tracking

range for the factory tted stylus (2.0g

– 3.0g).

2 Set the Bias adjustment slider to the

same number as the tracking weight.

For example, 2.0g tracking weight =

2.0g on the Bias slider.

ADVANCED SET-UP

A tracking pressure gauge is required to correctly apply the required down

force when changing the factory tted cartridge with a new or dierent

cartridge. The down force must correspond to the upper limit of the

cartridge maker’s recommended range.

1 Align the new cartridge correctly as shown.

2 Adjust the cartridge position in the head-shell so that the stylus tip is

vertically aligned with the front of the hole marked A.

3 Ensure the cartridge is sitting square in the head-shell before fully

tightening. Do not over tighten!

4 Set the Bias adjustment slider to the same number as the tracking

weight.

CONNECTING THE C 556

Use the external phono leads to connect the C 556 to an amplier. Use an

external Phono Preamplier (like one of NAD’s Phono Preamplier series) if

your amplier has no integrated phono stage.

Stop point

Tonearm

Counterweight

Bias slider

Stylus tip

ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 556 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info