Bedienungsanleitung NAD CI 940 (Seite 8 von 12) (Englisch)

745044

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

7 +12V TRIGGER IN/INPUT SENSE - OFF/AUTO

· This dual function switch alternates between sensing a +12V input

as applied through the +12V TRIGGER IN jack or sensing any active

input signal applied at ZONE 1 INPUT or ZONE 2 INPUT terminals.

· At AUTO setting and with the +12V trigger input of the CI 940

connected to the DC output jack of a compatible auxiliary

component, the CI 940 can be switched remotely from standby

mode to operating mode and vice-versa. Use a 3.5mm mini-jack to

pass +12V from the auxiliary equipment into the CI 940.

· If there is no 3.5mm mini-jack inserted at the +12V TRIGGER IN

jack and with the switch still at AUTO setting, the CI 940 will

instantaneously turn to operating mode from standby mode if it

senses any input signal (approximately above 20mV RMS input)

applied through ZONE 1 INPUT or ZONE 2 INPUT sockets.

· In the absence of a +12V trigger input or any input signal at ZONE

1 INPUT or ZONE 2 INPUT sockets and with OFF/AUTO switch set to

AUTO, the CI 940 will switch automatically to standby mode. Slide

the OFF/AUTO switch to OFF setting for the CI 940 to be normally

switched ON (or back to standby mode) using the front panel

STANDBY button.

· Refer also to the section below about “AUTOMATED TURN-ON LOGIC

(ATO LOGIC)”.

IMPORTANT NOTICE

With the rear panel POWER switch at ON position and the OFF/AUTO

switch at AUTO setting, the CI 940 cannot be switched ON using the front

panel STANDBY button. Slide the OFF/AUTO switch to OFF setting for

the CI 940 to be normally switched ON (or back to standby mode) using

the front panel STANDBY button.

NOTES

· Switch the rear panel POWER switch to ON position in order to make

use of the +12V TRIGGER IN or INPUT SENSE AUTO feature as well as the

front panel STANDBY button.

· It will take about 10 minutes for the CI 940 to go to standby mode when

the input signal source is turned OFF.

8 +12V TRIGGER INPUT

· The +12V TRIGGER input allows the CI 940 to be switched remotely

from standby mode to operating mode and vice-versa by ancillary

equipments such as a preamplier, AV processor, etc. The controlling

device must be equipped with a 12V trigger output to use this

feature.

· Refer also to the item above about “+12V TRIGGER IN/INPUT SENSE -

OFF/AUTO”.

9 FUSE HOLDER

· In the unlikely event a fuse may need to be replaced, unplug the AC

cord from the wall. Then, remove all connections from the amplier.

Use a athead screw driver or similar to open the fuse holder via

the slot indicated. With the screw driver in place, push and turn

counterclockwise to open the fuse holder.

· Only replace the fuse with the same type, size, and

specication - T6.3AL 250V.

IMPORTANT NOTICE

Do not use any substitute fuses of dierent types or with dierent ratings

or values. Failure to observe this precaution may cause damage to the

amplier circuits and may create a re hazard and/or defeat the safety

built into the amplier and may void the warranty.

10 AC MAINS INPUT

· The CI 940 comes supplied with a separate AC Mains cable.

· Before connecting the plug to the mains power source, ensure that

it is rmly connected to the CI 940’s AC Mains input socket rst.

· Always disconnect the mains power plug from the mains power

source rst, before disconnecting the cable from the CI 940’s AC

Mains input socket.

11 POWER SWITCH

· The POWER switch supplies the master AC mains power for the

CI 940.

· When the POWER switch is set to ON position and with +12V

TRIGGER IN/INPUT SENSE set to OFF, the CI 940 goes to standby

mode as indicated by the amber status of the Standby LED. Press

the front panel Standby button to switch ON the CI940 from

standby mode.

· If you intend not to use the CI 940 for long periods of time (such as

when on vacation), switch o the POWER switch.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD CI 940 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD CI 940

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info