Bedienungsanleitung NAD M12 (Seite 8 von 22) (Englisch)

745048

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

9 +12V TRIGGER OUT

• The +12V TRIGGER OUT is used for controlling external equipment

that is equipped with a +12V trigger input.

• Connect this +12V TRIGGER OUT to the other equipment’s

corresponding +12V DC input jack using a mono cable with 3.5mm

male plug.

• This output will be 12V when the M12 is at operating mode and 0V

when the unit is either OFF or in standby mode.

+12V TRIGGER IN

• Connect this +12V Trigger input to the remote device’s

corresponding +12V DC output jack using a mono cable with

3.5mm male plug. The controlling device must be equipped with a

+12V trigger output to use this feature.

• With this input triggered by a 12V DC supply, the M12 can be

switched ON remotely from standby mode by compatible devices

such as ampliers, preampliers, receivers, etc. If the 12V DC supply

is cut o, the M12 will return to standby mode.

10 IR IN

• This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the M12 from a remote location.

11 RS 232

NAD is a certied partner of AMX and Crestron and fully supports

these external devices. Check out the NAD website for information

about AMX and Crestron compatibility with NAD. See your NAD audio

specialist for more information.

• Connect this interface using RS-232 serial cable (not supplied) to

any Windows compatible PC to allow remote control of the M12 via

compatible external controllers.

• Refer to the NAD website for information about RS232 Protocol

documents and PC interface program.

12 POWER

• Supply the AC mains power to the M12.

• When the POWER switch is set to ON position, the M12 goes to

standby mode as shown by the amber status condition of the front

panel Power indicator. Press the front panel o (Standby) button or

HTRM 2 remote control’s [ON] button to switch ON the M12 from

standby mode.

• If you intend not to use the M12 for long periods of time (such

as when on vacation), switch o the POWER switch. With POWER

switched o, neither the front panel o (Standby) button nor HTRM

2 remote control’s [ON] button can activate the M12.

13 BALANCED

• Use the BALANCED analog audio input of the M12 if the external

source to be connected has BALANCED audio output. Superior

audio quality is ensured with the distinctive noise reduction

capability of BALANCED connection with XLR jacks.

14 AES/EBU IN

• Digital audio stream from professional audio sources like SACD/CD

Players or processors can be connected to this XLR connector.

• For high-end sources with higher sampling rates like 176kHz and

192kHz, it is highly recommended that such sources be interfaced

with the AES/EBU IN connector. The AES/EBU IN is well suited to

handle such sources with high sampling rate.

15 ANALOG AUDIO OUT (BALANCED, SINGLE-ENDED)

• The ANALOG AUDIO OUT is the main output port that connects the

M12 to the corresponding audio input ports of external ampliers.

This makes it possible to use the M12 as a pre-amplier to such

devices.

• The ANALOG AUDIO OUT consists of BALANCED and SINGLE-

ENDED output ports. It is recommended to use M12’s BALANCED

analog audio output if the external amplier has corresponding

BALANCED input port. Otherwise, use the SINGLE-ENDED analog

audio output to connect the M12 to the corresponding SINGLE-

ENDED, UNBALANCED or analog input port of an amplier.

16 GROUND TERMINAL

• Use this terminal to properly ground your M12 to a grounded AC

receptacle or a separate earth ground.

• The M12 can be connected to ground by connecting a ground lead

wire or similar to this ground terminal. After insertion, tighten the

terminal to secure the lead.

NOTES

• The above illustration shows the M12 being connected to ground via

a metal water pipe. There maybe other grounding conductor points

in your home. Consult with a licensed electrician to properly locate

or correctly install a grounding conductor in your home. NAD is not

responsible for any malfunction, damage or costs associated with the

installation, connection or grounding of your M12.

• The grounding wire is not supplied with your M12.

17 FUSE HOLDER

• Only qualied NAD service technicians can have access to this fuse

holder. Opening this fuse holder may cause damage thus voiding

the warranty of your M12.

18 AC MAINS INPUT

• The M12 comes supplied with two types of detachable mains

power cord. Connect corresponding end of the mains power cord

to the AC mains input of M12 and the plug connected to a mains

power source.

• Always disconnect the mains power plug from the mains power

source rst, before disconnecting the cable from the M12’s AC

Mains input socket.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M12 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info