Bedienungsanleitung NAD M12 (Seite 14 von 22) (Englisch)

667813

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

IR CHANNEL

The M12 has the capability to operate via Alternate IR channel. This is

practically useful if you have two NAD products that can be operated by

similar remote control commands. With alternate IR Channel, two dierent

NAD products can be controlled independently in the same zone by

setting each one to a dierent IR channel.

IR Channel Assignment

The M12 and the HTRM 2 remote control must be set to the same channel.

To change the IR Channel on the HTRM 2 remote control

• Include a channel number before the library code. For HTRM 2, library

code “100” is the default library table for “AMP” device. To select this

“AMP” library table for “IR Channel 0”, retain the library code “100”.

• If you want to load the “AMP” library table on “IR Channel 1”, prex the

library code with “1” to indicate association with “IR Channel 1”. Load

then the “AMP” library table using the code “1100”.

Sample setup of two NAD products on the same Zone

M12 and T 787 are both defaulted to IR Channel 0. If [OFF] button is pressed

on the HTRM 2 remote control (or HTR 8 remote control for the T 787), both

products will go to standby mode. Press [ON] and both products will power

up from standby mode.

To prevent both products from simultaneously going in and out of standby

mode along with other common commands, set each one to a dierent

IR channel. In this setup, we will keep T 787 and HTR 8 remote control

defaulted to “IR Channel 0”. As for M12, we will assign it to “IR Channel 1”; the

same applies to HTRM 2.

Set M12 and HTRM 2 to “IR Channel 1” via the following procedure.

M12

• Select “1” as the IR Channel setting of the M12.

HTRM 2

Begin by ensuring that the M12 is powered-up (“on”, not merely in standby).

1 Press and hold together the [AMP] and [A/V PSET] buttons until the

Learn LED (located between HTRM 2’s ON and OFF buttons) turns

steady green. Release both buttons.

2 While keeping the HTRM 2 pointed towards M12, press “1”, “1”, “0” and “0”

using HTRM 2’s numeric buttons.

3 Press [OFF]. If the M12 goes to standby mode, this indicates that the

library input is successful.

4 Press [ENTER] to accept the library code input and exit the Library

mode.

With both M12 and HTRM 2 set to “IR Channel 1”, the M12 can now be

remotely controlled independent of the T 787.

NOTE

Performing a Factory Reset for HTRM 2 will result to a return to the

factory default “IR Channel 0” setting.

USB MODE

The M12 is equipped with three USB input terminals – USB Front, USB Back

and Computer. Using either “USB Front” or “USB Back”, the M12 can play

back MP3/WMA/FLAC les stored in external USB (Universal Serial Bus) mass

storage devices. Use “Computer” to interface computer audio and directly

stream 24/192 PCM content from your PC or MAC.

DIGITAL USB FRONT/DIGITAL USB BACK USB TYPE A

• Supports playback of MP3, WMA and FLAC les

MP3/WMA: 48 kHz

FLAC: 24 bit/48 kHz

• FAT12/16 root directory up to 256 les (short names)

• FAT12/16/32 up to 65535 les (short names) per directory

• FAT le system limited to 2TB

• File and directory names limited to 64 characters

• Up to 16 maximum level of directories

• Compatible with USB version 1.1 and later.

COMPUTER USB TYPE B

• Supports 24 bit/192 kHz PCM content from PC or MAC

NOTE

Typical USB mass storage devices compatible with M12 include portable

ash memory devices and external hard drives (FAT32 formatted).

LISTENING TO USB DEVICE

1 Toggle [R SKIP/CH/SOURCE T] button to select “USB Front” or “USB

Back” source mode. If no external USB mass storage device is connected

to USB Front or USB Back input, “Please Insert Device” will be shown

in the touch panel display. If the connected USB mass storage device

does not contain any applicable MP3/WMA/FLAC les, “No les” will be

shown in the touch panel display.

2 Plug-in the external USB mass storage device to the USB input – MP3,

WMA or FLAC les or folders will be shown in the touch panel display.

3 Use [W/E/R/T] to select through the les or folder. Press [ENTER] to

start playback of selected le.

Ensure that HTRM2’s Device Selector is set to “MP” when using the

following USB playback buttons – j, 7/8, 4, RANDOM, REPEAT, DISP.

[g] button is not applicable for USB playback.

IMPORTANT NOTICE

Do not disconnect the USB mass storage device during playback as it

may damage the M12.

LISTENING TO COMPUTER

Use Type A to Type B cable connector to directly stream 24/192 PCM

content from your PC or MAC to the M12. Ensure that the Sound or Audio

device setting of your computer is set to “NAD USB Audio”.

MINIMUM PC SYSTEM REQUIREMENT

Microsoft Windows XP Service Pack 2 or higher, Microsoft Windows 7

FOR MAC USERS

Minimum Mac OS X Snow Leopard (version 10.6) and later versions

OPERATION

OTHER FEATURES

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M12 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info