Bedienungsanleitung NAD M15 HD2 (Seite 7 von 45) (Englisch)

745041

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

1 STANDBY LED

• This indicator will light up amber when the M15 HD is at standby

mode.

• When the M15 HD is powered up from standby mode, this indicator

will illuminate blue.

• If a Zone (Zone 2, Zone 3 or Zone 4) is ON and STANDBY button

is pressed to switch the M15 HD to standby mode, the VFD will

be extinguished but the STANDBY LED remains illuminated blue.

This indicates a Zone (Zone 2, Zone 3 or Zone 4) is still active. The

corresponding active Zone icon(s) will also remain displayed in the

VFD.

• In order to completely shut down the M15 HD with Zone 2, Zone

3 and/or Zone 4 still ON, press and hold STANDBY button until the

STANDBY LED turns amber.

• In the unlikely event that the M15 HD switches to protection state,

this indicator will illuminate red.

• When infrared command from the HTRM is received, this indicator

will also ash momentarily.

2 STANDBY BUTTON

• Press this button to switch ON the M15 HD from standby mode. The

Standby LED indicator will turn from amber to blue and illuminate

the VFD. Pressing the STANDBY button again turns the unit back to

standby mode.

• The M15 HD can also be switched ON from standby mode by

pressing any of the front panel buttons.

NOTES

• TherearpanelPOWERswitchmustbeintheONpositionfortheStandby

buttontoactivate.

• If“AutoTriggerIn”atTriggerSetupmenuisassignedto“Main”or“All”

andthe+12VTRIGGERINswitchissetto“AUTO”mode,thestandby

buttoninthefrontpanelaswellasthecorrespondingON/OFFfunction

keysintheHTRMremotecontrolwillbedisabledeectivelyhandling

thisfunctiontoanexternalcontroller.Slideto“OFF”the+12VTRIGGER

INswitchtomaintainnormalpowerON/OFFfunctionprocedures.

3 REMOTE SENSOR

• Point the HTRM remote control at the remote sensor and press the

buttons.

• Do not expose the remote sensor of the M15 HD to a strong light

source such as direct sunlight or illumination. If you do so, you may

not be able to operate the M15 HD with the remote control.

Distance: About 23ft (7m) from the front of the remote sensor.

Angle: About 30o in each direction of the front of the remote sensor.

4 VACUUM FLUORESCENT DISPLAY (VFD)

• Displays visual information about the current settings like the active

Source, volume level, listening mode, audio format, iPod-related

display information and other related indicators.

• Refer also to the item about DISPLAY SETUP under the USING THE

M15 HD - SETUP MENU segment of the OPERATION section.

5 VOLUME

• Use this control to adjust the overall loudness of the signal output at

AUDIO PRE-OUT.

• The default volume level is -20dB.

• The VOLUME knob is also used to increment/decrement other

adjustable parameters like Tone Controls.

6 3 SOURCE 4

• Toggle through the input selections - Source 1, Source 2, Source 3,

iPod, Source 5, Source 6, Source 7, Source 8 and Source 9.

• Refer also to the item about SOURCE SETUP under the USING THE

M15 HD - SETUP MENU segment of the OPERATION section.

7 INFO

• Show information as supplied by the applicable source.

• Toggle [INFO] button to display supplied information.

IDENTIFICATION OF CONTROLS

FRONT PANEL

4 5

1 2 3

109876

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M15 HD2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M15 HD2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info