Bedienungsanleitung NAD M33 (Seite 18 von 26) (Englisch)

745037

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

ENGLISH

If the Learn LED does not icker amber you may need to vary the distance

between the remotes. If the Learn LED turns red instead of green, the

source remote command could not be learned on that attempt.

Example: Learning “BD Pause”

Position the HTRM 2 and your BD player’s remote as described above.

1 On the HTRM 2, simultaneously press-and-hold [BD] and [RES]; the

Learn LED turns steady green.

2 Press the HTRM 2’s Pause [ j ] key; the Learn LED turns amber.

3 Press-and-hold the corresponding Pause key of your BD player’s remote

control; the HTRM 2’s Learn LED ickers amber and then turns solid

green. The command is learned.

4 Press [BD] again to exit the learning mode.

NOTES

• The DEVICE SELECTOR keys can themselves be congured to learn commands.

• Press and hold a congured DEVICE SELECTOR for at least 2 seconds to

execute a function assigned to the particular DEVICE SELECTOR key.

• A short press of a congured DEVICE SELECTOR will just switch the active

device.

CANCEL OPERATION

You can cancel conguring a key, by pressing the active Device Selector

key before the learn process is complete; the Learn LED will turn red.

PUNCH THROUGH

The HTRM 2’s “punch-through” function allows you to retain a function key

from one Device Select “page” to another, so that, for example, the AMP

[SURR MODE] function might still control the M33 when the BD Device

Selector page is active.

NOTE

The HTRM 2’s [VOL R/T] keys are pre-programmed as “punched-

through” for all Device Selector pages: [VOL R/T] will operate the

M33’s master-volume regardless of the currently selected device. The

[SURR] [CENT] and [SUB] Channel Volume controls similarly are pre-

programmed as punched-through.

SET A PUNCH THROUGH

1 Enter Learning Mode and press the desired button to be punched

through.

2 Press twice the Device Selector button of the destination device. The

status LED will turn green.

3 Press the Device Selector button again to exit Learning Mode.

Example: Punch-through AMP [SURR MODE] key to the BD “page”

1 On the HTRM 2, simultaneously press-and-hold [BD] and [RES]; the

Learn LED turns steady green.

2 Press [SURR MODE]; the Learn LED turns amber.

3 Press [AMP] twice; the Learn LED turns green.

4 Press [BD] again to exit the learning mode.

COPY A COMMAND FROM ANOTHER KEY

You may copy a command from any HTRM 2 key to any other key.

COPY A KEY FUNCTION

1 Enter Learning Mode.

2 Press the key that will contain the copied key. The Learn LED turns

steady amber.

3 If the key to be copied resides on another “page”, press rst the

corresponding Device Selector key and then press the desired key to

be copied. The Learn LED turns steady green.

4 Press the Device Selector key again to exit Learning Mode.

Example: Copy the Pause command from the CD page to the AMP [ j ]

button:

1 On the HTRM 2, simultaneously press-and-hold [AMP] and [RES]; the

Learn LED turns steady green.

2 Press Pause [ j ] ; the Learn LED turns amber.

3 Press [CD]; press Pause [ j ] ; the Learn LED turns green.

4 Press [AMP] again to exit the learning mode.

NOTE

The copy and punch-through functions are similar. However, if you

copy a command and then subsequently delete, or over-write the

original (source-key) command , the copied-to key’s command remains

unchanged. If you punch-through to a command and then delete or

over-write the original key, the punched-through functions also change

accordingly.

MACRO COMMANDS

A “macro” command is a series of two or more remote codes issued

automatically from a single keypress. You might use a macro to automate a

simple command sequence, such as, “Turn on the BD player and then press

PLAY”. Or you might compose an elaborate macro to power up an entire

system, select a source, choose a Listening Mode, and begin playback—

again, all from a single keypress. Each DEVICE SELECTOR and function keys

of the HTRM 2 can be stored into one macro.

NOTE

Macros are independent of the currently selected device.

RECORDING MACROS

1 Simultaneously press-and-hold the [MACRO] key and the HTRM 2

function key to be assigned the macro until the status LED turns green.

The macro button will also light up.

2 Press the sequence of function keys to be recorded into the macro.

3 Be sure to press rst the required Device Selector key for each function

(you may switch devices while recording the macro as many times as

necessary), allowing you to create macro containing commands from

more than one Device Selector “page.”

4 After entering the desired command sequence, press [MACRO] again to

store the macro; the Learn LED and [MACRO] key illumination will turn

o.

OPERATION

USING THE HTRM 2 REMOTE CONTROL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M33 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M33

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info