Bedienungsanleitung NAD M3e (Seite 10 von 20) (Englisch)

602914

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

FRONT PANEL CONTROLS (FIGURE 1)

1. Standby Button: The Standby Button turns on and to standby the M3. This button will

only function when the Status Condition LED is either blue representing the on-state, or

amber representing the standby state.

2. Status Condition L.E.D.:

Standby: When this L.E.D. is amber the M3 is in the standby state.

On: When this L.E.D. is blue the M3 is operating in the on-state.

Protection: When this L.E.D. is red the M3 is in a protection state.

The M3 has sensors for abnormally high internal heat and signal level conditions that

would damage either the M3 or speakers. When these conditions return to normal, the

M3 reverts to the on-state. In the event the Status Condition L.E.D. is red and PROTECT

displays in the VFD for longer than 5 minutes; switch off the M3 via the rear panel POWER

switch, check all speaker cables and connections for short-circuits. Resume normal

operation. If the Status Condition L.E.D. continues to light red and PROTECT displays in

the VFD, contact qualified NAD service personnel for repair.

3. Vacuum Florescent Display (VFD): The VFD provides visual information on all of the

M3's important modes, settings, and functions for both main and second zone locations.

4. listen (input selection): Press the listen button to select an input. A press longer than

one second will advance the input selection to the next input as follows; DISC, CD, TUNER,

INPUT 4, INPUT 5, INPUT 6, BALANCED and then return to DISC. Release the listen button

to stop the sequence.

Assigning User Names (input selection): Renaming inputs is advantageous when using

auxiliary equipment not representing the default inputs. For example, a CD-player with

balanced outputs would connect to the balanced input. Rename the balanced input to

CD-Player as follows;

Press and hold simultaneously the listen and record / Z2 buttons until the cursor flashes.

Rotate the volume (set up) control to the letter "C" then press the listen button to lock

the selection and advance the cursor. Continue the procedure for the remaining letters of

the name. Press the record / Z2 button to save the new user name.

NOTES: There is a maximum of 20 letters to each name. The variables are; lowercase letters,

uppercase letters, numbers, and miscellaneous punctuation symbols.

Record each name you assign into the chart on page 17 to aid you for future reference in

the event you wish to change the hook-up and assignment of the inputs.

5. record / Z2 (second zone output): Press the record / Z2 button to select the input as

the recording source. A press longer than one second will advance the source selection to

the next input as follows; OFF, DISC, CD, TUNER, INPUT 4, INPUT 5, INPUT 6, BALANCED,

LOCAL, and then return to OFF. Release the record / Z2 button to stop the sequence.

Furthermore, the ZR3 remote control will allow direct selection of inputs (see ZR3 Remote

Control).

NOTE: The record / Z2 can monitor all inputs. The record / Z2 will maintain its last state even

if the M3 is set to standby. The M3 must be in its on state in order to use the record / Z2.

About the M3 Dual Mono Integrated Amplifier:

Identification of controls

M3 10262005.qxd 1/3/2006 2:49 PM Page 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M3e Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M3e

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info